Fine Woodworking Magazine - Craftsman Wall Cabinet (Plans) - 2008.pdf

(18367 KB) Pobierz
416058500 UNPDF
14 ¾ in.
4 5/16 in.
square
5 1/8 in.
11 ¾ in.
5 1/8 in.
Craftsman Wall Cabinet
by Ian Ingersoll
31 ½ in.
½ in.
8 ¾ in.
Top, 1 in. x 8 ¾ x 14 ¾ in.
8 in.
12 ¾ in.
11 ¾ in.
Rabbet, ½ in x ¼ in.,
accepts subtop.
A Drawer that Tilts Out
A small rabbet accepts a bead
that allows the drawer to tilt.
Groove, ½ in. x ¼ in.,
houses back.
Dadoes, ½ x ¼ in.,
accept shelves.
Pivoting stop keeps
drawer from falling
out of case.
Subtop
Side, ¾ in. x 6 in.
x 29 ½ in.
Drawer
5 in. deep
Shelf, ½ in. x
5 ¼ in. x 10 ¾ in.
Radius,
8 in.
Drawer stop, 3/8 in.
x 3/8 in. x 1 ¼ in.
Notch, 1/2 in. wide,
accepts drawer stop.
Front rabbet, ¼ in. x
5/8 in., accepts side
Back, ½ in. x
10 ¾ in. x 29 ½ in.
Brad, 1 ¼ in.
Drawer Front Section
Groove, ¼ in. x ¼ in.
and set back 3/8 in.
accepts pivot bead
on drawer front.
Drawer front
Bottom, 1 in. x 7 ¼ in.
x 12 ¾ in.
Hole, ¾ in. dia.
Pivot bead, 1/4 in.
x 1/4 in.
Copyright © 2008, The Taunton Press
416058500.019.png 416058500.020.png 416058500.021.png 416058500.022.png 416058500.001.png 416058500.002.png 416058500.003.png 416058500.004.png 416058500.005.png 416058500.006.png 416058500.007.png 416058500.008.png 416058500.009.png 416058500.010.png 416058500.011.png 416058500.012.png 416058500.013.png
 
Molding, ¼ in. x ¼ in.,
holds glass in place
Glass, 1/8 in. thick
Setting in Muntins and Glass
Panes for the glass
With two 45 º cuts on each
muntin end, the muntins
are laid in place, and the
miters are marked on the
rails and stiles.
Muntin,
¼ in. x
5/8 in.
Miter, 45 º,
accepts
muntin
Cutting miters in the
rails and stiles
Use a small saw to cut
miters on the door frame,
which will accept the
muntin ends.
Stub tenon,
¼ in. x ¼ in.
Groove, ¼ in.,
accepts door
panel.
Crossing the glass
Add the muntins, to give
the appearance of divided
panes of glass. Mark the
stock for a half-lap joint
where the muntins cross,
then cut the joint on the
tablesaw.
Stile, ¾ in. x 1 ¼ in.
x 29 ½ in.
Finishing a groove
The rear wal of the groove
in the stiles and rails is
removed to accept glass.
Rail, ¾ in. x 1 ¼ in. x 11 ¾ in.
CUTLIST
Door panel, ¼ in. thick.
Component
Qty.
Dimensions
Top
1
1 x 8 ¾ x 14 ¾
Subtop
1
½ x 5 ¼ x 10 ¾
Shelf
1
½ x 5 ¼ x 10 ¾
Miter, 45 º cut into
rails and stiles.
Bottom
1
1 x 7 ¼ x 12 ¾
Back
1
½ x 10 ¾ x 29 ½
Side
2
¾ x 6 x 29 ½
Door stile
2
¾ x 1 ¼ x 29 ½
Door rail
3
¾ x 1 ¼ x 11 ¾
Window muntins
2
¼ x 5 / 8 x 9 7 / 8
Window molding
4
¼ x ¼ x 9 ¾
Drawer front
1
5 / 8 x 9 ¾ x 8
Drawer side
2
5 / 8 x 4 x 8
Drawer back
1
5 / 8 x 9 ¾ x 8
Drawer bottom
1
¼ x 4 ¼ x 9
Door panel
1
1/4 x 9 ¾ x 15 ¾
Drawer stop
1
3 / 8 x 3 / 8 x 1 ¼
416058500.014.png 416058500.015.png 416058500.016.png 416058500.017.png 416058500.018.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin