TD-W8961ND_szybka instrukcja.pdf
(
9154 KB
)
Pobierz
Installation
Note
The product model shown in this QIG is TD-W8961ND, as an example.
Note
Please use only wired network connections to configure the router.
Power down all your network devices, including your computer(s) and
the
Modem Router. If you currently use a modem, disconnect it now - the
Modem Router will replace your current modem.
Connect your computer to the
Port labeled “1~4” on the
Router with an Ethernet cable.
Connect the splitter to the wall
jack using a telephone line,
then use the other telephone
line to directly connect it to the
ADSL port on the Router and
the MODEM port of the
splitter, also have the PHONE
port of the splitter connected
to a telephone.
If no telephone is needed, please connect the ADSL port of the Router to
the wall jack using the telephone line directly.
Note
1
Plug the provided Power
Adapter into the Power jack
on the back of the Router and
the other end to a standard
electrical wall socket.
Power on all your network devices and then check to see if the LEDs of the
Router display normally as the diagram below describes.
POWER: Solid light
ADSL: Solid light or flashing
WLAN: Solid light or flashing
LAN: Solid light if the corresponding port is connected
If the LEDs display abnormally, please check to see if all the cable
connectors (power adapter, phone line and Ethernet cable) are well
connected to your device. With the phone line well connected, if the
ADSL LED turns off after flashing, please contact your ISP to ensure that
your Internet connection is active.
Note
To configure the device, you can either run the setup CD-ROM (method one),
or run the Web-based Quick Setup Wizard (method two). TP-LINK strongly
recommends that you run the setup CD-ROM.
Note
2
Insert the provided Resource
CD into your CD-ROM drive.
The Setup Wizard will
automatically pop up on
your computer’s screen.
Please select your product
model and click
Start Setup
Then a flash video will pop up and
show you how to connect your
devices. After that, the
Easy Setup
Assistant
will start.
Click
NEXT
, and then follow
the step-by-step instructions
until
you
complete
the
configuration
The configuration has now been completed. Please skip to
Step 3
“Testing the
Internet Connection”
.
3
Login
Open your web browser and
type
192.168.1.1
in the address
bar and press
Enter
A dialog box will prompt you for the
User name
and
Password
. Enter
the default values and click
OK
.
User name: admin
Password: admin
Click
OK
Note
If the dialog box does not pop up, please refer to
T3
in the
Troubleshooting
guide and
T2
will give you some help if you forget the password.
The web management page will
display after a successful login.
Click
Quick Start
4
Internet Parameters Configuration
This page will then display.
Click
RUN WIZARD
Click
NEXT
Select the appropriate
Time
Zone
for your location from
the drop-down list
Click
NEXT
Choose the
Connection Type
given
by your ISP.
If
PPPoE/PPPoA
is selected, please
proceed to
A
;
If
Dynamic IP
is selected, please
skip to
B
;
If
Static IP
is selectedLjplease skip to
C
;
If
Bridge Mode
is selected, please
skip to
D
.
Click
NEXT
Bridge mode is not recommended because multiple computers are not
permitted to share Internet access in this mode.
Note
5
Plik z chomika:
jimasek
Inne pliki z tego folderu:
TD-W8961ND_szybka instrukcja.pdf
(9154 KB)
TD-W8961ND-01-New(1).jpg
(356 KB)
TD-W8961ND-02-New.jpg
(354 KB)
TD-W8961ND-03-New.jpg
(346 KB)
TD-W8961ND_instrukcja.pdf
(1430 KB)
Inne foldery tego chomika:
Archer AX11000
Archer AX6000
Archer AX72
Archer AX73
Archer AX90
Zgłoś jeśli
naruszono regulamin