Katalog ogolny Nidec 2011.pdf
(
15442 KB
)
Pobierz
TURN
ADJUST
tilt
RAISE
OPEN
ROTATE
MOVE
close
SPIN
DRIVE TECHNOLOGY
2011/12
THE
NIDEC MOTORS & ACTUATORS
DC MOTOR RANGE
MOTORS
WITHOUT GEARING
MOTORS WITH
SPUR GEAR
MOTORS WITH
WORM GEAR
GMP
→
Smaller diameter motors with single & double
output shafts
→ Nominal torque ............... 0.05 – 0.1 Nm
→ No load speed ................. 2700 – 3250 min
-1
GMK
GML
→
Higher torque single output shaft motors
→ Nominal torque ............... 0.12 – 0.4 Nm
→ No load speed ................ 2200 – 5250 min
-1
GMAG
GMPI
→
Motors that can address all your in-line drive
requirements where you need higher torque,
lower speed rotation
→ Nominal torque ............... 0.2 – 4 Nm
→ No load speed ................ 17 – 200 min
-1
GMPD
GMPG
→
Low/medium torque with perpendicular
output shafts
→ Nominal torque ............... 0.5 – 4 Nm
→ No load speed ................ 21 – 540 min
-1
GMPS
→
Actuators fitted with a lead-screw to drive
your linear motion needs
→ Nominal axial force ......... 1 – 2 kN
→ No load speed ................ 6 mm/s
DCK31
DCK35
→
Cost competitive medium torque range
worm drive motors
→ Nominal torque ............... 3 – 6 Nm
→ No load speed ................ 14 – 270 min
-1
SWMK
SW2K
SW2L
→
Weight optimized medium torque range
→ Nominal torque ............... 0.8 – 8 Nm
→ No load speed ................ 48 – 350 min
-1
SWMV
SWMG
→
Powerful medium & high torque worm gear
motors
→ Nominal torque ............... 3 – 20 Nm
→ No load speed ................ 27 – 220 min
-1
→
TABLE OF CONTENTS
NIDEC MOTORS & ACTUATORS
→
IMPORTANT EXPLANATORY INFORMATION
......................................................................................
2
→
DC MOTORS wIThOUT gEARINg
....................................................................................................
6
SERIES 0220 (GMP)
.................................................................................................................
7
SERIES 0272 (GMk)
................................................................................................................
17
SERIES 0273 (GML)
................................................................................................................
25
→
DC MOTORS wITh SPUR gEAR
......................................................................................................
34
SERIES 0202 (GMaG)
..............................................................................................................
35
SERIES 0231 (GMPi)
...............................................................................................................
41
→
DC MOTORS wITh wORM gEAR
....................................................................................................
48
SERIES 0320 (GMPd)
..............................................................................................................
49
SERIES 0225 (GMPG)
.............................................................................................................
67
SERIES 0223 (swMP)
.............................................................................................................
79
SERIES 0321 (GMPs)
..............................................................................................................
91
SERIES 0266 (dCk31)
...........................................................................................................
101
SERIES 0268 (dCk35)
...........................................................................................................
133
SERIES 0270 (swMk)
...........................................................................................................
149
SERIES 0277 (sw2k)
............................................................................................................
163
SERIES 0278 (sw2L)
............................................................................................................
181
SERIES 0291 (swMV)
...........................................................................................................
191
SERIES 0292 (swMG)
...........................................................................................................
199
→
INDEX
.......................................................................................................................................
204
1
→
IMPORTANT EXPLANATORY INFORMATION
NIDEC MOTORS & ACTUATORS
Subject to change and error, also of a technical nature.
Therefore use only product drawings for design purposes.
These are available from your representative.
be tested for their suitability in the customer’s particular
application. Specific motor designs for special customers.
Motors in this catalog are not intended for the consumer.
In accordance with EU regulations, these products do not
require CE certification marking. Some motors have cus-
tomer specific designs. They require new tooling for new
designs.
The catalog illustrations do not all correspond to DIN
requirements. The operating values indicated are valid for
20° C ambient temperature. In all cases the motors should
→
TERMS, SYMBOLS AND UNITS ACCORDING TO DIN
Symbol
Unit
Term
U
N
[V]
Rated voltage
n
0
[min
-1
]
No-load speed ± 10%
M
N
[Nm]
Nominal torque at the output shaft
M
A
[Nm]
Starting torque
i
Gear ratio
J
R
[kgm
2
] x 10
-6
Armature load inertia
R
[mΩ]
Armature resistance, 2/4 commutator bars
L
[mH]
Armature inductance, 2/4 commutator bars
Drawing
dimensional drawing
Shaft
dimensions of shaft ends
Wiring diagram
motor wiring diagram
Connection
dimensions and positions of motor connections
Materials
BRZ = bronze, KST = plastic, ST = steel,
HGW = resinbonded fabric
Direction of rotation
when looking onto
motor shaft
The curves show the speed and the current as a function of the torque.
These are average values at room temperature.
Divergences of ± 10 % are possible in the series.
Preferred direction of rotation:
Worm gear motors have a preferred direction of rotation, indicated in
the drawings by a larger arrow. If the motor rotates against the preferred
rotation direction, power decreases by approx. 10 %.
CCW CW
2
Drive Technology 2011/12
→
IMPORTANT EXPLANATORY INFORMATION
NIDEC MOTORS & ACTUATORS
→
CONVERSION OF TORQUE VALUES
(VALUES ROUNDED FOR PRACTICAL USE)
Nm
Ncm
pcm
kpcm
kpm
oz in
in lbs
ft lbs
Nm
1
100
10.2 x 10
3
10.2
0.102
141.6
8.85
0.738
Ncm
10
-2
1
102
1.02 x 10
-2
1.02 x 10
-3
1.42
8.85 x 10
-2
7.38 x 10
-3
pcm
9.8 x 10
-5
9.8 x 10
-3
1
10
-3
10
-5
1.39 x 10
-2
8.68 x 10
-4
7.23 x 10
-5
kpcm
9.8 x 10
-2
9.8
1000
1
10
-2
13.9
0.868
7.23 x 10
-2
kpm
9.8
980
10
5
100
1
1390
86.8
7.23
oz in
7.06 x 10
-3
0.706
72
7.2 x 10
-2
7.2 x 10
-4
1
6.25 x 10
-2
5.2 x 10
-3
in lbs
0.113
11.3
1152
1.15
1.15 x 10
-2
16
1
8.3 x 10
-2
ft lbs
1.36
135.58
13,825
13.8
0.138
192
12
1
→
CONVERSION OF FORCES
(VALUES ROUNDED FOR PRACTICAL USE)
N
kp
p
oz
lbf
N
1
0.102
102
3.6
0.225
kp
9.8
1
1000
35.27
2.2
p
9.8 x 10
-3
10
-3
1
3.53 x 10
-2
2.2 x 10
-3
oz
0.278
2.83 x 10
-2
28.35
1
6.25 x 10
-2
lbf
4.45
0.445
453.6
16
1
→
CONVERSION OF POWER
(VALUES ROUNDED FOR PRACTICAL USE)
kW
PS
HP
kpm/s
kcal/s
kW
1
1.36
1.34
102
0.239
PS
0.735
1
0.986
75
0.176
HP
0.746
1.01
1
76
0.178
kpm/s
9.8 x 10
-3
1.33 x 10
-2
1.32 x 10
-2
1
2.34 x 10
-2
kcal/s
4.2
5.7
5.6
427
1
→
CONVERSION OF TEMPERATURES
t
C
[°C] Celsius
t
F
[°F] Fahrenheit
T
K
[K] Kelvin
T
R
[°R] Rankine
3
Plik z chomika:
asikadi
Inne pliki z tego folderu:
V60e C3 Nidec(1).pdf
(1407 KB)
U60T200901 Nidec(1).pdf
(834 KB)
TA300DCA Nidec(1).pdf
(191 KB)
Silniki Nidec 2010.pdf
(8310 KB)
Oznaczenia Nidec.pdf
(1434 KB)
Inne foldery tego chomika:
Akumulatory i baterie
Bezpieczniki
Cewki
Diody
Ledy wyswietlacze
Zgłoś jeśli
naruszono regulamin