b-wing.pdf

(120 KB) Pobierz
5712521 UNPDF
B-Wing Starfighter
© James B. Raasch III, 12/14/97
1)
2)
3)
Begin with a bird base, colored side out, and
fold the front flap all the way up. Turn the
model over. Note that no shading is shown
because there are no color changes, and it
makes some of the folds easier to see.
Fold the triangular peak all the way down.
Fold tip ‘A’ to tip ‘B’. Unfold.
4)
5)
6)
Fold crease ‘A’ to crease ‘B’.
Fold the top flap up along the existing
crease. This will become the cockpit.
Fold the triangular peak all the way up.
Page 1 of 6
5712521.027.png 5712521.028.png 5712521.029.png 5712521.030.png 5712521.001.png 5712521.002.png
B-Wing Starfighter
© James B. Raasch III, 12/14/97
7)
8)
9)
Fold the bottom flap all the way up. This will
become the main wing
Fold the wing flap down, about half way
between the crease you just made and the
edge formed from creasing the top flap.
The exact amount is not important.
Squash the sides of the wing flap so that the
edges are vertical. Again, the exact amount
is not important, but try to line up the
intersection of the top of the horizontal
creases and the cockpit flap with the vertical
crease. The intersection is hidden in the
diagram.
10)
11)
12)
Fold the triangular peak down at the crease
you made in step 8.
Fold the model in half along the vertical axis
from right to left.
Squash-fold the top flap up and to the left.
Repeat on the flap on the back. These will
Page 2 of 6
5712521.003.png 5712521.004.png 5712521.005.png 5712521.006.png 5712521.007.png 5712521.008.png
B-Wing Starfighter
© James B. Raasch III, 12/14/97
13)
14)
15)
Petal fold the s-foil right. Repeat behind.
Fold the flap up and to the left along a 45 0
line. Repeat behind.
Unfold the fold on the left side that was
made when you made the petal-fold in step
13. Repeat behind.
16)
17)
18)
Fold the front half of the s-foil back along
the centerline, and tuck it under the top
sheet of paper. Repeat behind.
Fold the flap up along the horizontal.
Repeat behind.
Fold the s-foil down as far as you can. This
crease will be horizontal, and will fall along
the edge of the engine pod. Repeat behind.
Page 3 of 6
5712521.009.png 5712521.010.png 5712521.011.png 5712521.012.png 5712521.013.png 5712521.014.png
B-Wing Starfighter
© James B. Raasch III, 12/14/97
19)
20)
21)
Inside-reverse fold the tip of the s-foil to
make the wingtip cannon. If you treat the
flap you folded inside in step 17 as one side,
and do the reverse between that flap and
the single sheet, you will end up with the
bottom of the cannon white. Repeat behind.
Outside-reverse fold the end of the main
wing to make the main wing cannon.
Finish forming the main wing by folding this
flap inside the body. The midpoint of the
45 0 line made by the outside-reverse fold
makes the bottom endpoint of the crease.
The exact position, however, is not
important, as long as it looks good. Repeat
behind.
22)
23)
24)
Fold the tip of the cockpit flap down to the
bottom horizontal crease.
Squash the flap up and to the left.
Fold the flap over as far as you can to the
right.
Page 4 of 6
5712521.015.png 5712521.016.png 5712521.017.png 5712521.018.png 5712521.019.png 5712521.020.png
B-Wing Starfighter
© James B. Raasch III, 12/14/97
25)
26)
27)
Fold the lower half of the flap up.
Fold the tip down to the crease that formed
in the last step. Repeat behind.
Fold the tip to the vertical edge and unfold.
28)
29)
30)
Fold the flap down along the crease made in
step 26. Repeat behind.
Fold the tip of the nose in along the crease
made in step 28.
Fold the back of the engine pod into the
body. Repeat behind.
Page 5 of 6
5712521.021.png 5712521.022.png 5712521.023.png 5712521.024.png 5712521.025.png 5712521.026.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin