Alarm Clock Instruction For Use
Table of Contents
Preface and Quality Assurance
Using instruction for Chinese time signal clock
DV Structure diagram
DV product introduction & handling instruction
DV File storage instruction Relevant parameters of DV
Power source and fittings
Troubleshooting
Precautions
Preface This Instruction will guide you how to use the product. Meanwhile it provides the necessary information related to the product, such as the information for operating and handling. You are recommended to read the Instruction carefully and understand all contents herein before operating. Please keep the Instruction carefully. We hope this product satisfied with your demand and sever you better. Product Assurance This product is with FCC and CE certificate and had inspected by the authorized organizations where was found to comply with the recommended indexes. User is under our safety assurance when operating this product.
Instruction For Use for Time-signal Clock
I. Basic functions 1. 5 buttons: HR, MIN, SET, LIGHT, TALK/SNZ;
2. The time & minute can be displayed in a 3.5 bit LCD panel. Time-showing system of 12 hours and 24 hours is available;
3. Multiple rings for choice: Beep, cock, etc. 5 melodies for option.
4. The time alarm will be triggered every 10 minutes if the clock is on the snooze function. It can alarm 6 times maximally.
5. Two on-the-hour alarm functions for choice;
6. The ring of “Beep” will be become louder generally. And it will last 1 minute;
7. If adopting the melody as the ring, the clock will alarm when the melody ends.
II. Function operation 1. When switching the power on, the whole LCD will display; after the ring of a melody ends, the clock will display time;
2. Press “Set” button under the Time mode to set as per the following sequences (the display will flash simultaneously):
Time setting → Alarm setting → On-the-hour alarm setting 3. Press “HR” button under the Time Setting mode to set hour and “MIN” button to set minute; 4. Press “HR” button under the Alarm Setting mode (Symbol: ) to set hour and “MIN” button to set minute. Press “SNZ” button when alarming, the clock will re-alarm every 10 minutes, and will send alarm by 6 times at most; 5. Under the On-the-hour Alarm Setting mode (the symbol of alarm and the on-the-hour alarm will flash):
It will open and close the function (Symbol: ) by pressing the “HR” button, but send alarm during the time from 7:00am to 9:00pm (Symbol: ); it can activate the inactivate the alarm ring by pressing “MIN” button (Symbol: ).
6. Under the Time Mode and if the “HR” button is pressed, it can shift the hour system (12/24 hour system); by pressing “MIN” button, it can select the alarm ring. 7. Under any modes, it can turn the background light off by pressing the “LIGHT” button. 8. Under any modes, it can report the time by pressing the “TALK” button.
DV Using Instruction
1、Alarm Clock
I. Structure Diagram
Time-telling button
Lens
TF card
Rotational cover
Ti
Turn off
Turn on
Receiver
Electric Clock Function Button
2、Remote controller
Switch button
Sender
Take a photo
Video
motion detection video
Sound recording
II. Product Introduction This product is a high-resolution 30-frame (640X480, 1280*960) remote video surveillance clock, with an external TF Card. As a multifunctional high-tech product, the product is available multiple functions, such as: video, sound recording, induction video, take a photo, cyber chat, electric alarm clock and file storage; with the high-capacity battery, it can last recording for about 12 hours continuously and audio recording for 25 hours continuously; besides, the product can replace the high-resolution video with 2 million pixels, sound and file automatically, Meanwhile, the product is designed the multiple languages for telling the time. It supports 32GB storage. Its TF card can be used for a long time and remote controller can be easy to handle. With the best imperceptibility, this product will be as your ideal assistant to prevent theft and get evidence.
III. Handling Instructions
1. Open the rotational cover at the right side, insert the TF card and turn “ON” to get ready.
2. Use the remote controller to aim to the receiver of the clock and press " " to start. When the blue lamp is on and the clock is under the stand by mode.
3. Press to start recording video. After the blue lamp flashes 3 times and then turns off, it start recording. stop pressing , it will save the video file and return to the “holding state” , and the blue lamp will be on (the default time length for video recorded is 20 minutes).
4. Press button to start recording a sound; after the blue lamp flashes 1 time and turns off, it will be put into the working order; Press again, it will save the sound file and return to the “holding state” , and the blue lamp will be on (the default time length for sound recorded is 20 minutes);
5. Press button to get in photo taking mode. It will take a photo if pressing this button again. When pressing this button, the blue lamp will flash; after taking the photo, it will return to the stand by.
6. Press button to get in motion detection mode, then the blue lamp will flash quickly. If a moving object is detected, the blue lamp will flash slowly by two times and the device will be start to record video. If there is no moving object to be detected, the blue lamp will return to “Quick-flash: and get in motion detection mode (the default length for the video file is 3 minutes);
7. Press button, it will turn the device off and the blue lamp will be off.
8. When the switch is “ON”, insert the USB cable and then press button on the remote controller, the device will access to the U-disc mode.
9. PC camera function: Please install the driver software which is saved in the Compact Disc before operating; Turn on the device by pressing on the remote controller when the device is under the mode of “ON”, insert USB cable to connect the computer; at this time, it will access to PC CAM mode;
10. Charging: Place the chief switch to “OFF” position, insert USB adapter, and the red lamp will be on; When it is full, the red lamp will be off. You can charge it too by connect this device to a computer ( Please use only the adapter provided with the device together; if the device getting hot or occurs other unexpected situations whilst charging, please disconnect the adapter's power source);
11. Reset: If the product stops working under illegal operation or other unclear reasons, please place the switch of the device to “OFF” position, and then to “ON” position. It will reset the product accordingly;
12. When the battery is low capacity, the blue lamp will keep flashing or the screen display will be unclear. Then please charge it immediately. If it is used off, the file will be saved automatically;
13. Recorder date: Run the writertime file( in CD disc) when the camera connect with computer. And then ,the video time is the same computer.
14. File update: please install “Network Installer” from the installation disc; use the remote controller to open the clock, and then insert the USB cable in 10 seconds; afterwards, the computer will open an interface automatically; click “Program Upgrade”, it will open a dialogue box; afterwards click “Update”. When ① DRAM Timing, select 0X35
When ② DRAM Size, select “8M”; afterwards, press “OK” to upgrade; several minutes later, press “Confirm” button.
15. ...
barteck