wri-p_instructions_111709.pdf
(
673 KB
)
Pobierz
722187216 UNPDF
WRI-P
Wired Remote Input Control Interface
11-17-09
Compatible with Pioneer in-dash
navigation units that lack an IR receiver
but have a wired remote input.
Installation Instructions
Pacific Accessory Corporation
Before You Start
A. Prepare for the installation.
• If possible, install the WRI-P while you are installing the new head unit.
• Plan a general installation location for both the WRI-P infrared eye and the control body.
• If you are installing the WRI-P in conjunction with a SWI-PS, please refer to the SWI-PS instructions for all wiring
and programming information.
IP-BUS cable
IP-BUS input
Fuse
Jack for the SWI-PS
Antenna jack
Power
To Infrared Eye
Wiring Connections
Step 1.
Connect the BLACK
wire to ground (-).
Step 2.
Connect the RED wire
to switched +12V.
Black
Red
Veriication:
Wire
or location registers
a constant (-) when
probed.
Black
Red 12V+ (Switched)
Veriication:
Wire reg-
isters +12V when the
ignition key is turned
to the ACC or ON posi-
tions.
1
Step 3.
Connect the 3.5mm stereo plug on 5 pin Molex to the wired remote input on
the back of the radio..
Step 4
Mount the infrared eye in a suitable location
Back of Radio
Wired Remote In
Black
Red 12V+ (Switched)
Black
Red 12V+ (Switched)
To Suitable
Location
Step 5
If applicable, install the SWI-PS and connect
the 3.5mm plug to the SWI-PS input on the
side of the WRI-P
WRI-P Functions
CD-R510 Function
VOLUME + Volume up
VOLUME - Volume down
BAND Band
SRC Source
ATT Mute/Attenuate
PGM Phone Status
OFF/H Answer Call
ON/H End Call
Joystick Function
UP Preset +
DOWN Preset -
RIGHT Seek >>
LEFT Seek <<
Center Voice Activation
WRI-P
SWI-PS
Note: CLEAR
button is for self
testing of WRI-P.
See
troubleshooting
section below
Compatibility Notes
1. The voice recognition command via wireless remote is not supported on the following models: AVIC-F700BT, AVIC-F900BT,
AVIC-U310BT, AVIC-X710BT, and AVIC-X910BT.
2. PAC recommends the use of the Pioneer CD-R510 or CXC9115 remote for maximum compatibility with the WRI-P. Other
Pioneer remotes may work, but some functions / buttons may not be supported.
Troubleshooting
The WRI-P has a self test mode which can determine if it is sending and receiving the proper signals. Follow the steps below to
engage the self test mode:
1. Connect the module to a 12v source (do not apply power yet).
2. Connect the 3.5mm output plug on 5 pin Molex to the 3.5mm input on the side of the module.
3. Connect the IR receiver to the WRI-P.
4. Power up the WRI-P
5. Using the CD-R510 remote, point the remote at the IR receiver and press the CLEAR button on the remote to start the test.
The LED will blink 9 times while testing the analog outputs and inputs then pause for a second. It will blink 3 times to conirm it
passed the test.
2
Paciic Accessory Corporation - Santa Ana, CA 92705
866-931-8021• www.pac-audio.com
Plik z chomika:
Cleverservice
Inne pliki z tego folderu:
AVICNETenglishNA.7z.001
(10240 KB)
AVICNETenglishNA.7z.002
(10240 KB)
AVICNETenglishNA.7z.003
(10240 KB)
AVICNETenglishNA.7z.004
(10240 KB)
AVICNETenglishNA.7z.005
(10240 KB)
Inne foldery tego chomika:
Pliki dostępne do 21.01.2024
Angielski
Audiobook
AVIC F900 F700
Do aut - VAG
Zgłoś jeśli
naruszono regulamin