desk-organizer-polka na biurko.pdf

(382 KB) Pobierz
Desk Organizer
D
esk Organizer
Too much work and not enough desk space? Make better use of your work surface with
this handy organizer. There’s room for scores of desk necessities, and the top surface is large
enough to accommodate books and even a clock.
-1-
108207086.046.png 108207086.047.png 108207086.048.png 108207086.049.png 108207086.001.png 108207086.002.png 108207086.003.png 108207086.004.png 108207086.005.png 108207086.006.png 108207086.007.png 108207086.008.png 108207086.009.png 108207086.010.png 108207086.011.png 108207086.012.png 108207086.013.png 108207086.014.png 108207086.015.png 108207086.016.png 108207086.017.png 108207086.018.png 108207086.019.png 108207086.020.png 108207086.021.png 108207086.022.png 108207086.023.png 108207086.024.png 108207086.025.png 108207086.026.png 108207086.027.png 108207086.028.png 108207086.029.png 108207086.030.png 108207086.031.png 108207086.032.png 108207086.033.png 108207086.034.png 108207086.035.png 108207086.036.png 108207086.037.png 108207086.038.png 108207086.039.png 108207086.040.png
Materials List
  12 linear feet of 1 x 12 pine
  9 linear feet of 1 x 4 pine
  6 linear feet of ¾”-wide cove molding
  6 linear feet of 3-1/4”-wide crown molding
Hardware
  40 1” (2d) finish nails
  20 1-1/4” wood screws
  50 1-5/8” wood screws
Special Tools and Techniques
  Miter
Cutting List
Code
Description
Qty. Materials Dimensions
A Vertical Divides
4 1 x 12 pine 9” long
B Shelves
2 1 x 12 pine 11-5/8” long
C Top/Bottom
2 1 x 12 pine 38” long
D Front Trim
1 1 x 4 pine
40” long
E. Side Trim
2 1 x 4 pine
12-1/4” long
F Back Trim
1 1 x 4 pine
35” long
G Cove Molding
¾” x ¾”
Cut to fit
H Crown Molding
3-1/4” wide Cut to fit
Building the Center Compartments
1. Cut four Vertical Dividers (A) from 1 x 12 pine, each measuring 9 inches.
2. Cut two Shelves (B) from 1 x 12 pine, each measuring 11-5/8 inches.
3. Place two Vertical Dividers (A) on edge on a flat surface, parallel to each other, and 11-5/8
inches apart. Center one Shelf (B) horizontally between the two Vertical Dividers (A), as
shown in Figure 1 . Apply glue to the meeting surfaces, and screw through the Vertical
-2-
108207086.041.png
Dividers (A) into the edges of the Shelf (B), using three 1-5/8” wood screws.
4. Repeat Step 3 to attach the remaining Shelf (B) to the remaining two Vertical Dividers (A).
Adding the Top and Bottom
1. Cut two Top/Bottoms (C) from 1 x 12 pine, each
measuring 38 inches.
Figure 1
2. Place one Top/Bottom (C) on edge, on a flat
surface. Place one shelf assembly (A and B) 1-
1/2 inches from one end of the Top/Bottom (C),
as shown in Figure 2 . Apply glue to the meeting
surfaces, and screw through the Top/Bottom (C)
into the ends of the Vertical Dividers (A). Use
three 1-5/8” wood screws on each joint.
Figure 1
3. Repeat Step 2 to attach the remaining shelf
assembly (A) and B) 1-1/2 inches from the
opposite end of the same Top/Bottom (C).
4. Center the remaining Top/Bottom (C) over the assembly. It should overhang the outermost
Vertical Dividers (A) by 1-1/2 inches on both ends. Apply glue to the meeting surfaces, and
screw through the Top/Bottom (C) into each of the Vertical Dividers (A). Use three 1-5/8”
wood screws on each joint.
Adding the Trim
1. Cut one Front Trim (D) from 1 x 4 pine measuring 40 inches.
2. Miter each end of the Front Trim (D) at opposing 45-degree angles, as shown in Figure 3 .
3. Cut two Side Trims (E) from 1 x 4 pine, each measuring 12-1/4 inches.
4. Miter one end of each of the Side Trims (E) at a 45-degree angle, as shown in Figure 4 .
5. Place the Front Trim (D) over the edge of the Top/Bottom (C), as shown in Figure 5. The
Front Trim (D) should overhang the Top/Bottom (C) by 1 inch on the front and both sides.
Apply glue to the meeting surfaces, and screw through the Front Trim (D) into the
Top/Bottom (C) using 1-5/8” wood screws spaced every 5 inches.
-3-
108207086.042.png
Figure 2
Figure 3
6. Place one Side Trim (E) over the ends of the Top/Bottom (C), with the miter toward the
Front Trim (D), as shown in Figure 5 . The trims should overhang the sides by 1 inch.
Apply glue to the meeting surfaces, and screw through the Side Trim (E) into the
Top/Bottom (C) using three 1-1/4” wood screws.
7. Repeat Step 6 to attach the remaining Side Trim (E) to the opposite end of the Top/Bottom
(C).
8. Cut one Back Trim (F) from 1 x 4 pine measuring 35 inches.
-4-
108207086.043.png
Figure 4
9. Fit the Back Trim (F) between the two Side Trims (E), flush with the back edge of the
Top/Bottom (C), as shown in Figure 5 . This piece does not overhang. Apply glue to the
meeting surfaces, and screw through the Back Trim (F) into the Top/Bottom (C), using 1-
5/8” wood screws spaced every 5 inches.
Figure 5
-5-
108207086.044.png 108207086.045.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin