CIXS201GBD.PDF

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00

www.cobra.it

MAKE

CITROEN

MOD. XSARA 2 YEAR. 01 ﬁ

PETROL

DIESEL

ALARM/SIREN

POSITION

Position the compact alarms and the sirens behind the driver’s side headlamp. To

do that it is suggested to take off the air filter.

CENTRAL UNIT POSITION

Position the modular systems and the modules under the dashboard, driver’s

side.

POWER SUPPLY

+ 30: connect to the general supply wire of the fuse box.

- 31: connect with a cable terminal directly to the car body.

IGNITION WIRE

+ 15/54: connect to the wire coming out of the 3A fuse (to insert) foreseen as

supply for additional accessories located in the shunting box placed on the side of

the battery.

DIRECTION INDICATORS

Connect to the wires at the positions nr.14 and nr.15 in the 16 way black

connector coming out of the (BSI) accessories operating central located under

the fuse box.

ELECTRIC WINDOWS

Positive control signal

Front window, driver’s side:

connect to the GREY wire marked nr. 6010 located at the position nr. 4 of the

window control switch, driver’s side.

Front window, passenger’s side:

cut the wire marked nr. 6061, at the position nr. 5, of the window control switch,

passenger’s side.

For the connection to the driver’s side front window, it is suggested to refer to the

diagram nr. 68.

CENTRAL DOORS LOCKING Negative control signal

Wire interruption original control

Cut the wire at the position nr. 8 located in the wiring harness coming out of the

26 way blue connector, coming out of the (BSI) accessories operating central

placed under the fuse box. Refer to the diagram nr. 71 for the antithefts of the

Bridge serie or to the diagram nr. 71A for the antithefts of the 3100 serie.

IMMOBILISATION POINT

Gasoil pump

Cut the wire marked nr. 1201 located at the E6 position, in the 46 way black

connector, placed in the lower part of the fuse box, in the engine compartment, in

correspondence of the fuse nr. 52.

STARTER CUT OFF

50: Cut the WHITE wire located in the wiring harness coming out of the connector

of the ignition key.

BONNET SWITCH

Install an additional switch on the front headlamp support plate, driver’s side. It is

necessary to bore also the plastic cover.

DOORS AND BOOT SWITCH Connect to the wire at the position nr. 14, of the 26 way blue connector, coming

out of the (BSI) accessories operating central located under the fuse box.

Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed

as per the instructions given on the product installation manual.

cixs201gbd.doc

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00

www.cobra.it

FITTING DIAGRAM N° 68

Diagram to make the windows locking with automatism on

XSARA 2

Antitheft central with Relay to reverse Original switches with automatic

BROWN/WHITE the polarity windows locking system

(time to 24s) left window right window

1052

+30

1 2 3 4 5

BROWN/WHITE

DIODES

1N4004

Antitheft central with the Temporized relay Original switches with automatic

BROWN Art. 1055 windows locking system

left window right window

+30

1055

1 2 3 4 5 6 7

BROWN

DIODES 1N4004

Note:

The above diagrams are to make electric windows locking on vehicles with “MAGIC” system

automatism on both the motors.

In any case, if the motor (passenger’s side) does not have the automatism, it is necessary to install the

art. 2980 module for windows locking.

Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed

as per the instructions given on the product installation manual.

cixs201gbd.doc

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00

www.cobra.it

FITTING DIAGRAM N° 71

To make the central doors locking on

CITROEN BERLINGO – EVASION – XSARA 2 mod. 2001

(for “Bridge” car alarms)

VIOLET/ORANGE ORANGE GREY/BLACK VIOLET

Towards the

driver’s side door

Connector coming out of the central doors

locking unit of the vehicle, located behind

the glove compartment, passenger’s side.

Note: The wire indicated in the alarm fitting instructions of Citroen Berlingo, Evasion and Xsara 2 must

be interrupted as per the above drawing. Pay attention that the position of the wire that must be

interrupted changes as per the vehicle.

Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed

as per the instructions given on the product installation manual.

cixs201gbd.doc

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00

www.cobra.it

FITTING DIAGRAM N°71A

To make the central doors locking on

CITROEN BERLINGO – EVASION – XSARA 2 mod. 2001

(for 3100 serie car alarms)

VIOLET/WHITE ORANGE GREY/BLACK VIOLET

ORANGE/WHITE

Towards the

driver’s side door

Connector coming out of the central doors

locking unit of the vehicle, located behind

the glove compartment, passenger’s side.

Note : The wire indicated in the alarm fitting instructions of Citroen Berlingo, Evasion and Xsara 2 must

be interrupted as per the above drawing. Pay attention that the position of the wire that must be

interrupted changes as per the vehicle.

Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed

as per the instructions given on the product installation manual.

cixs201gbd.doc

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: