PS4 ZB4-501-UM3-UM4 Interface Converter h1371g.pdf

Hardware, Configuration

and Functional Description

ZB4-501-UM3/-UM4 Interface Converter

S40-AM-UM3/-UM4 Application Module

Telecontrol Modules

05/00 AWB2700-1371GB

1st published 1999, edition date 08/99

2nd reprint 2000, edition date 05/00,

See list of modifications on page II

Author: Peter Roersch

Editor: Thomas Kracht

Translator: Dominik Kreuzer

All brand and product names are trademarks or

registered trademarks of the owner concerned.

tion.

No part of this manual may be reproduced in any

form (printed, photocopy, microfilm or any other

process) or processed, duplicated or distributed by

means of electronic systems without written

permission of Moeller GmbH, Bonn.

Subject to modifications.

Warning!

Dangerous electrical voltage!

Before commencing the installation

• Disconnect the power supply of the device.

• Ensure that devices cannot be accidentally

restarted.

• Verify isolation from the supply.

• Earth and short circuit.

• Cover or enclose neighbouring units that

are live.

• Follow the engineering instructions (AWA)

of the device concerned.

• Only suitably qualified personnel in accordance

with EN 50 110-1/-2 (VDE 0 105 Part 100) may

work on this device/system.

• Before installation and before touching the

device ensure that you are free of electrostatic

charge.

• The functional earth (FE) must be connected to

the protective earth (PE) or to the potential

equalisation. The system installer is responsible

for implementing this connection.

• Connecting cables and signal lines should be

installed so that inductive or capacitive interfe-

rence do not impair the automation functions.

• Install automation devices and related opera-

ting elements in such a way that they are well

protected against unintentional operation.

• Suitable safety hardware and software

measures should be implemented for the

I/O interface so that a line or wire breakage

on the signal side does not result in undefined

states in the automation devices.

• Ensure a reliable electrical isolation of the low

voltage for the 24 volt supply. Only use power

supply units complying with IEC 60 364-4-41

(VDE 0 100 Part 410) or HD 384.4.41 S2.

• Deviations of the mains voltage from the rated

value must not exceed the tolerance limits given

in the specifications, otherwise this may cause

malfunction and dangerous operation.

• Emergency stop devices complying with

IEC/EN 60 204-1 must be effective in all opera-

ting modes of the automation devices.

Unlatching the emergency-stop devices must

not cause restart.

• Devices that are designed for mounting in

housings or control cabinets must only be

operated and controlled after they have been

installed with the housing closed. Desktop or

portable units must only be operated and

controlled in enclosed housings.

• Measures should be taken to ensure the proper

restart of programs interrupted after a voltage

dip or failure. This should not cause dangerous

operating states even for a short time. If neces-

sary, emergency-stop devices should be imple-

mented.

• Wherever faults in the automation system may

cause damage to persons or property, external

measures must be implemented to ensure a safe

operating state in the event of a fault or

malfunction (for example, by means of separate

limit switches, mechanical interlocks etc.).

05/00 AWB2700-1371GB

List of modifications to the manual AWB2700-1371GB

Edition

date

Page

Description

New

Modi-

fica-

tion

Omit-

ted

05/00

Gene-

ral

Complete revision by the addition of

ZB4-501-UM4

05/00 AWB2700-1371GB

Contents

About This Manual

1 About the Modules

Purpose of the ZB4-501-UM3/-UM4

Hardware and software requirements

Setup

– ZB4-501-UM3

– ZB4-501-UM4

2 Engineering

ZB4-501-UM3/-UM4 in the Suconet K network

Power supply

– ZB4-501-UM3

– ZB4-501-UM4

Connections

– Suconet K connections

– RS232 port

Electromagnetic compatibility

– Earthing the data cables

3 Configuration

Configuring the software

Configuring the ZB4-501-UM4 hardware

– Activating/deactivating bus terminating resistors

– Setting the address

4in

Operating phase

Startup behaviour

Shutdown behaviour

5iis

LED function at startup

LED function during operation

Failure Codes

Contents

05/00 AWB2700-1371GB

6 Application Module

Software requirements

Installation

– S40-AM-UM3

– S40-AM-UM4

Function block UM3_COM

– Inputs and outputs

Function block UM4_COM

– Inputs and outputs

Data transfer

– Sending data

– Receiving data

Appendix 43

Receiving data 43

Technical data 44

– ZB4-501-UM3 44

– ZB4-501-UM4 45

– General EMC specifications for automation equipment 46

Dimensions

– ZB4-501-UM3

– ZB4-501-UM4

Index

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: