DARWIN SWIRE-GW-DP h1590g.pdf

Connection

System

SmartWire

SWIRE-GW-DP

Hardware and

Function Description

11/06 AWB1251-1590GB

Rückenbreite festlegen! (1 Blatt = 0,106 mm)

All brand and product names are trademarks or registered

trademarks of the owner concerned.

1 st published 2006, edition date 11/06

Author: Wolfgang Nitschky

Editor: Heidrun Riege

Translator: David Long

No part of this manual may be reproduced in any form

(printed, photocopy, microfilm or any other process) or

processed, duplicated or distributed by means of electronic

Warning!

Dangerous electrical voltage!

Before commencing the installation

• Disconnect the power supply of the device.

• Ensure that devices cannot be accidentally

restarted.

• Verify isolation from the supply.

• Earth and short circuit.

• Cover or enclose neighbouring units that

are live.

• Follow the engineering instructions (AWA)

of the device concerned.

• Only suitably qualified personnel in

accordance with EN 50110-1/-2

(VDE 0105 Part 100) may work on this

device/system.

• Before installation and before touching

the device ensure that you are free of

electrostatic charge.

• The functional earth (FE) must be

connected to the protective earth (PE) or

to the potential equalisation. The system

installer is responsible for implementing

this connection.

• Connecting cables and signal lines should

be installed so that inductive or capacitive

interference does not impair the

automation functions.

• Install automation devices and related

operating elements in such a way that they

are well protected against unintentional

operation.

• Suitable safety hardware and software

measures should be implemented for the

I/O interface so that a line or wire breakage

on the signal side does not result in

undefined states in the automation

devices.

• Ensure a reliable electrical isolation of the

low voltage for the 24 volt supply. Only

use power supply units complying with

IEC 60364-4-41 (VDE 0100 Part 410) or

HD 384.4.41 S2.

• Deviations of the mains voltage from the

rated value must not exceed the tolerance

limits given in the specifications, otherwise

this may cause malfunction and dangerous

operation.

•Emergency stop devices complying with

IEC/EN 60204-1 must be effective in all

operating modes of the automation

devices. Unlatching the emergency-stop

devices must not cause restart.

• Devices that are designed for mounting in

housings or control cabinets must only be

operated and controlled after they have

been installed with the housing closed.

Desktop or portable units must only be

operated and controlled in enclosed

housings.

• Measures should be taken to ensure the

proper restart of programs interrupted

after a voltage dip or failure. This should

not cause dangerous operating states even

for a short time. If necessary, emergency-

stop devices should be implemented.

• Wherever faults in the automation system

may cause damage to persons or property,

external measures must be implemented to

ensure a safe operating state in the event

of a fault or malfunction (for example, by

means of separate limit switches,

mechanical interlocks etc.).

11/06 AWB1251-1590GB

Contents

About this manual

Intended users

Additional device manuals

Reading convention

1 About the PROFIBUS-DP gateway

SWIRE-GW-DP

System overview

Design of the SWIRE-GW-DP

Description of function

2 Installation 9

Set PROFIBUS-DP station address 9

Connect SmartWire connection cable 10

Connect supply voltages 11

Connect PROFIBUS-DP 12

Connection assignment PROFIBUS-DP 13

Terminating resistors 14

EMC-conformant wiring of the network 14

Potential separations 15

Data transfer rates – automatic baud rate detection16

Maximum distances/bus cable lengths

3 Commissioning

Initial switch on

Meaning of the status LEDs

–Ready-LED

– U-Aux-LED

– SmartWire LED

– PROFIBUS LED

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: