HOCRV97GBB.PDF

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00

www.cobra.it

HONDA

CR-V

YEAR 97 ﬁ

PETROL

DIESEL

MAKE

MOD.

ALARM/SIREN

POSITION

Position the compact alarms and the sirens in the engine compartment, on the support

panel at the shock absorber, driver’s side. Position the modular systems and the

modules under the dashboard, driver’s side.

POWER SUPPLY

+ 30: connect to the general supply wiring in the fuse box.

- 31: connect to the car body.

IGNITION WIRE

+ 15/54: connect to the 0,5 mm 2 YELLOW/RED wire with GREY reference located in

the wiring harness coming out of the 24 way light blue connector above the fuse box.

DIRECTION INDICATORS

Connect to the 0,75 mm 2 GREEN/YELLOW wire with GREY reference and to the

GREEN /RED wire with GREY reference located in the wiring harness of the 6 way

connector, in the front part of the fuse box.

ELECTRIC WINDOWS

Positive control signal

Front window, driver’s side:

cut the 1,5 mm 2 RED/BLUE wire.

Front window, passenger’s side:

cut the 1,5 mm 2 BLUE/YELLOW wire with BROWN reference.

Rear window, driver’s side:

cut the 1,5 mm 2 GREEN/YELLOW wire with BROWN reference.

Rear window, passenger’s side:

cut the 1,5 mm 2 YELLOW wire with GREY reference.

These connections should be effected in the wiring harness coming out of the 14 way

transparent connector of the control switches.

CENTRAL DOORS LOCKING

Negative control signal

Connect to the 0,5 mm 2 BLUE/RED wire with GREY reference (unlock) and to the 0,5

mm 2 BLUE/WHITE wire with GREY reference (lock) located in the wiring harness

coming out of the 14 way grey/white connector linked to the central doors locking unit,

inside the driver’s side door. Refer to the diagram nr. 126.

IMMOBILISATION POINT

Fuel pump

Cut the 0,5 mm 2 YELLOW/RED wire with GREY reference located in the 24 way light

blue connector, above the fuse box.

STARTER

+50: Cut the 2,5 mm 2 BLACK/WHITE wire located in the wiring harness coming out of

the 3 way brown connector, behind the fuse box.

BONNET SWITCH

Install an additional switch on the bonnet bumper, near the original rubber in

correspondence of the driver’s side headlamp.

DOORS SWITCH

Connect to the 0,5 mm 2 LIGHT GREEN/RED wire with GREY reference located in the

wiring harness coming out of the 20 way grey connector, behind the sill cover, driver’s

side.

BOOT SWITCH

Connect to the 0,75 mm 2 BLUE/BLACK wire with GREY reference located in the wiring

harness coming out of the 14 way blue connector, in the superior part of the fuse box.

Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed

as per the instructions given on the product installation manual.

hocrv97gbb.doc

SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00

www.cobra.it

FITTING DIAGRAM N°126

Diagram to make the locking and the opening of the doors on

HONDA CR-V, HR-V, LOGO

(for antitheft with 6 wires locking, with serie Bridge using Art. 1044)

VIOLET VIOLET/WHITE ORANGE GREY/BLACK

YELLOW/BLACK ORANGE/WHITE

Locking pulse

Opening pulse

Towards central doors locking unit Towards door motor

Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed

as per the instructions given on the product installation manual.

hocrv97gbb.doc

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: