Group_23_Restraints.pdf

(5002 KB) Pobierz
Untitled Document
5HVWUDLQWV
83070884.026.png
 
83070884.027.png 83070884.028.png
5HVWUDLQWV
5HVWUDLQWV
5HVWUDLQWV
6SHFLDO7RROV
5HI 1R
7RRO1XPEHU
’HVFULSWLRQ
4W\
07HAZ-SG00500
Deployment Tool
1
07PAZ-0010100
SCS Short Connector
1
07SAZ-TB4011A
SRS Inflator Simulator
1
07TAZ-SZ5011A
SRS Simulator Lead C
1
07TAZ-001020A
Backprobe Adapter, 17 mm
2
07XAZ-S1A0200
SRS Simulator Lead E
1
07XAZ-SZ30100
SRS Simulator Lead F
1
07YAZ-S3A0100
SRS Simulator Lead H
1
07WAJ-0010100
DLC Pin Box
1
* 1 : Included in SRS Tool Set 07MAZ-SM5000B
* 2 : Use with the stacking patch cords from T/N 07SAZ-001000A, Backprobe Set.
83070884.001.png 83070884.002.png 83070884.003.png 83070884.004.png
6HDW%HOWV
6HDW%HOWV
&RPSRQHQW/RFDWLRQ,QGH[
5($5&(17(56($7%(/7 ’(7$&+$%/($1&+25 Replacement, step 1 on page 23-9 ; Inspection, page 23-12
5($5&(17(56($7%(/7%8&./(DQG/()75($5
6($7%(/7%8&./(
Replacement, step 1 on page 23-11
5($56($7%(/7
Replacement, page 23-8 ; Inspection, page 23-12
)52176($7%(/7
Replacement, page 23-4 ; Inspection, page 23-12
5($5&(17(56($7%(/7 ’(7$&+$%/($1&+25
DQG5,*+75($56($7%(/7%8&./(
Replacement, step 1 on page 23-10
)52176($7%(/7%8&./(6
Replacement, step 1 on page 23-6
83070884.005.png 83070884.006.png 83070884.007.png 83070884.008.png 83070884.009.png 83070884.010.png 83070884.011.png
5HVWUDLQWV
6HDW%HOWV
)URQW6HDW%HOW5HSODFHPHQW
For some models: SRS components are located in this
area. Review the SRS component locations (see page 23-
14) and the precautions and procedures (see page 23-16)
in the SRS section before performing repairs or service.
Remove the upper anchor cover (A), and remove
the upper anchor bolt (B).
NOTE: Check the front seat belts for damage, and replace
them if necessary. Be careful not to damage them during
removal and installation.
)URQW6HDW%HOW
Make sure you have the anti-theft code for the
radio, then write down the frequencies for the
preset buttons (for some models).
Disconnect the negative battery cable, and wait at
least 3 minutes before beginning work.
Slide the front seat forward fully.
Disconnect the seat belt tensioner connector (A),
and detach the harness clip (B) from the retractor
(C). Remove the upper retractor mounting bolt (D),
and the lower retractor bolt (E), then remove the
front seat belt (F) and retractor.
Pull the lower anchor cover (A) back, and remove
the lower anchor bolt (B).
Remove the center pillar lower trim panel (see
page 20-76) .
)RUZDUG
83070884.012.png 83070884.013.png 83070884.014.png 83070884.015.png 83070884.016.png 83070884.017.png 83070884.018.png 83070884.019.png 83070884.020.png
6HDW%HOWV
Remove the center pillar upper trim (see page 20-
76) .
8SSHUDQFKRUEROWFRQVWUXFWLRQ
833(5$1&+25
%2/7
Remove the shoulder anchor adjuster (A).
&2//$5
833(5$1&+25
7227+(’/2&.
:$6+(5
%86+,1*
/RZHUDQFKRUEROWFRQVWUXFWLRQ
Install the seat belt in the reverse order of removal,
and note these items:
635,1*
:$6+(5
:$6+(5
/2:(5$1&+25
%2/7
Apply liquid thread lock to the upper anchor bolt
before reinstallation.
:$6+(5
Check that the retractor locking mechanism
functions (see page 23-12) .
Assemble the washers, collar, and bushing on the
upper and lower anchor bolts as shown.
Before installing the anchor bolts, make sure there
are no twists or kinks in the seat belt.
7227+(’/2&.
:$6+(5
%86+,1*
:$6+(5 /2:(5$1&+25
Make sure the seat belt tensioner connector is
plugged in properly.
(cont’d)
Reconnect the negative cable to the battery.
Enter the anti-theft code for the radio, then enter the
customer’s radio station presets (for some models).
83070884.021.png 83070884.022.png 83070884.023.png 83070884.024.png 83070884.025.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin