east start T podłaczenie.pdf

Installation instructions.

Comfort Timer

with 7-day preset capability.

EasyStart T

Contents

Introduction Page

• Please read first ..................................................................................................... 3

• General information / safety instructions ................................................................. 3

• ”Ventilate“ mode..................................................................................................... 3

• Purpose ................................................................................................................. 3

• Technical specifications .......................................................................................... 4

• Scope of supply ..................................................................................................... 4

• Additional parts (option).......................................................................................... 4

Installation instructions

• Installation .............................................................................................................. 5

– Install timer ....................................................................................................... 5

– Electrical connection .......................................................................................... 6

– Install room temperature sensor (optional).......................................................... 6

– Install external temperature sensor (optional)...................................................... 6

• Combine EasyStart T timer with EasyStart T timer.................................................. 7

Initial commissioning

• Perform initial commissioning ................................................................................. 8

– Apply operating voltage ..................................................................................... 8

– Automatic detection........................................................................................... 8

– Set the time and operating time ......................................................................... 8

– Configure system ........................................................................................ 9, 10

– Permissible unit combinations.......................................................................... 10

– Test timer......................................................................................................... 10

Miscellaneous

• Reset function ...................................................................................................... 11

What to do if …?

• Displays ............................................................................................................... 12

– ndiA display ..................................................................................................... 12

– Menu item A D does not appear in the menu bar .............................................. 12

– Menu item does not appear in the menu bar............................................... 12

Service .................................................................................................................... 12

Diagnosis

• Perform heater diagnosis .................................................................................... 13

• Display system configuration ............................................................................... 14

Circuit diagrams

• Parts list circuit diagrams .................................................................................... 15

• Assignment of the circuit diagrams to the different AIRTRONIC , AIRTRONIC M and

AIRTRONIC L heater models ................................................................................ 15

• Circuit diagrams (at the end of the installation instructions)

Declaration of conformity (at the end of the installation instructions)

Introduction

Please read first

Before you start to install the timer, please

ensure you carefully read through these

installation instructions.

These installation instructions contain

important information, which you require

to install the timer.

(Order No. 22 1000 32 07 00) must be

installed (see Circuit Diagrams, Item

3.1.17).

“Ventilate” mode is not possible in all

other heater models.

In the “ventilate” switch setting of

HYDRONIC water heaters the vehicle

blower is directly controlled by bypassing

heat mode and in AIRTRONIC air heaters

the heater’s blower is bypassed in the

same way.

General information / safety instruc-

tions

In ADR mode, immediate operation wit-

hout temperature display only is possible.

We recommend installing the temperature

sensor available as an option in order to

enable use of all the timer’s functions.

If the temperature sensor (optional) is

connected the heater start is automatical-

ly calculated for water heaters.

In air heaters the temperature sensor is

used for temperature display.

Please note!

“Ventilate” or “heat” mode must be se-

lected before switching on the heater.

• “Ventilate” mode is not provided for

upgraded independent heaters.

• If you have any further questions about

“ventilate” mode, please call the service

phone number (see page 12).

• The circuit diagrams are at the end of

these installation instructions.

Important!

Note and comply with the safety instruc-

tions and general information given in

the heater’s documentation and in the

EasyStart T operating instructions.

Purpose

The EasyStart T timer is used to switch

on / off and preset the switching-on time,

operating time and operating mode of the

heater and / or add-on unit installed in

the vehicle

„Ventilate“ mode

If the symbol is not displayed in the

menu bar, “ventilate” mode is only pos-

sible in the heater for the heater models

under certain prerequisites:

• With the water heaters HYDRONIC

(B / D 4 W S, B / D 5 W S, B / D 4

W SC and B / D 5 W SC): the “heat /

ventilate” switch (Order No. 22 1000

31 89 00) must be installed (see Circuit

Diagram, Item 3.1.9).

• With the air heaters AIRTRONIC /

AIRTRONIC M: the mini controller

Please note!

Improper use and use outside the spe-

cified area of use cancels all liability and

warranty.

Introduction

Technical specifications

Operating voltage: 12 V / 24 V

Dimensions: 36 x 51 x 10.5 mm

Operating temperature: –40 °C to +80 °C

LCD: readability is ensured from –20 °C

to +60 °C.

Please note!

At temperatures below –10 °C the display

becomes sluggish, i.e. the flashing se-

quence is slower.

Scope of supply

1 12 V / 24 V timer

1 Cap

1 Fixingscrew

1 Base

1 Flat connector housing

9 Junior Power Timer push on sleeve

1 Push on sleeve housing

2 Lockingclasps

1 Drillingtemplate

Additional parts (option)

– Room temperature sensor

(Order No.: 22 1000 32 49 00)

– External temperature sensor

(Order No.: 25 1482 89 41 00)

– “ON / OFF” button

(Order No.: 22 1000 32 84 00)

– Console

(Order No.: 22 1000 51 32 00)

Installation instructions

Installation

Install timer

Install the timer in a suitable place on the

dashboard within the driver‘s line of vision

and connect according to the sketch

and circuit diagrams at the end of this

documentation.

• Use the self-adhesive drilling template

provided to position and drill the holes.

Remove the drilling template when you

have finished drilling.

• If necessary, the foam pad base can be

used to balance out any unevenness.

To do this, pull off the protective plastic

sheet and stick the base onto the timer.

• Feed the heater lead harness through

the ø 8 mm drill hole.

• Preassemble the timer with expansion

plug in the ø 6.5 mm drill hole.

• If the foam pad base is used, pull off the

second protective plastic sheet too.

• Push or screw the fixing screw into the

expansion bolt to fasten the timer .

• Pull off the protective plastic sheet on

the cap and stick in the cap.

• Fix the flat connector of the timer lead

harness in the 9-pin flat connector

housing.

• Push in the locking clasp at the flat

connector housing.

Installation

1 2

1 Timer

2 Fixingscrew

with cap

3 Lead harness to heater

4 Room temperature sensor (optional)

5 Self-tapping screw C2.9 x 19

(1x, optional)

6 Push on sleeves (9x)

7 Push on sleeve housing

8 Flat connector housing

9 Timer lead harness

10 Drilling template

11 Foam pad base

12 Locking clasps

Please note!

• Only install the timer inside the vehicle.

• When selecting the installation position,

ensure the display is clearly visible, if

necessary use the console (optional).

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: