Ship Modeling Simplified Part 4.pdf

108

PART IV

Finishing Her Up

"Young Officers sometimes feel a diffidence in

soliciting information; either from a fear of

exposing their ignorance, or from an idea that such

a request may be treated with ridicule. A reference,

like a work of this nature, which can be consulted

with privacy, will obviate the difficulty: it was not a

secondary consideration in the prosecution of it."

— A Young Sea Officer's Sheet Anchor, 1819

That intricately rigged, finely crafted

model now sitting in front of you knows

you by now. It's watched your moods

swing as you waded through the proc-

ess. A while back you were a nervous

novice, tentative, unsure about what to

do next. Now you've got a nearly fin-

ished ship model at your fingertips; and

you're feeling good, maybe even cocky.

That's fine, but don't get carried

away; though you might feel like it,

you're not finished yet. Stay with the

cautious, careful streak we've been on

since we first laid the keel. A silly mis-

take now will throw some unwanted

gloom into a festive moment.

Putting the finishing touches on your

model is a lot like the proverbial icing

on the cake. The cake might be delicious,

but if the frosting is slopped on no one's

going to notice.

The final touches will focus attention

on your fine work, not detract from it. A

smartly fitted anchor, an impeccable

paint job, and nicely appointed boats and

davits set off by a flying flag — these

109

things can really add to your ship's looks.

Take a deep breath and let's get going.

We're almost there now.

service boats, fishing boats, and lifeboats.

Some of the simpler boats were flat bot-

tomed, some were planked smooth, and

others were clinker-built or lapstraked

(like a clapboard house).

Most kits provide small boats; some

are precarved, some are stamped ply-

wood plank-on-frame. Some kits just

supply plans and instructions. Let's take

a look at some of them.

Most of the precarved boats are

pretty good — just the right size and

shape — but they require additional

BOATS , ANCHORS ,

PAINT , AND FLAGS

BOATS

Depending on its duties, a ship might

have cause to use a number of boats —

110

The first thing to do is to carve out

the inside of the boat a little more. Use

a small sanding drum on an electric drill

at a reduced speed and then some gentle

filing. Hand sand any rough spots, then

stain or paint the inside.

Next install the frames. Make them

from a thin wood strip; bend to match

the curve of the hull and glue in place.

Install the floorboards and then the

stringers. The stringers support the ends

of the seats (or thwarts) and run parallel

to the gunwale — the upper edge of the

boat's side. Hold the stringers in place

temporarily with small pins until the

glue dries. The bow seat and the stern

seat are made of thin (1 mm) plywood;

cut the bow seat in a triangular shape

and the stern seat in a "U" shape. Both

can be planked for a better look. Bend

the caprail — the top of the gunwale —

along the boat's lines; drill two closely

spaced holes in the caprail on each

side of the boat midway between the

seats and insert short pins in the holes

to simulate thole pins, which accom-

modated oars in the days before oar-

locks. Cut small wood triangles and

erect them on the ends of the seats and

against the hull to form reinforcing knees.

Now you can paint the outside of the

boat.

Some kits will provide plank-on-

frame boat kits. These can be very chal-

lenging — if not downright difficult —

to build properly.

Why?

Some kits supply frames stamped on

easily breakable 1 mm plywood. You

also may find that some of the frames

are so out of proportion that the finished

hull looks like a cucumber. Another

problem: you must remove the frames

when the hull is completed, and this is

no easy task. Then there are the frames

that are too weak to support the plank-

ing. . . .

I am not saying that all plank-on-

frame boat kits are impossible to build.

Some can be constructed if you have a

lot of patience and stamina. Following

are some of the tricks that will help you

accomplish it more readily:

• Make sure that the frames are cen

tered on the keel properly before

gluing.

• Cover the outside edges of the

frames with masking tape so that the

planks will not stick to them.

• Install a strip inside the frames as a

temporary stringer to help keep the

frames in place.

• Taper the planks just as you would

on a ship model.

• Use double planking, making sure

that the second layer of planks

overlaps the seams on the first

layer.

• After the planking is done remove

the frames, sand the inside of the hull

smooth, and install the ribs.

• If the boats look really bad, discard

them and buy precarved ones.

work to make them look more authen-

tic.

111

Boats were stored on ships in differ-

ent ways. Some were secured upside

down on deckhouse roofs or on deck.

The boats were set on two crosstimbers

to avoid warping the keel and were

lashed down with ropes to rings inserted

on the timbers.

Some boats were set on cradles

rightside up and lashed to the deck.

Some ships carried their service boats

on davits — the arms used to hoist and

hold the boat — fixed on the side or stern

of the ship. A boat on davits will need

blocks and tackles to be raised or low-

ered.

You can see a typical arrangement

of a boat stowed on davits in the illus-

tration on page 109. The davits can be

installed either inboard or outboard.

Some davits will swing inboard to stow

the boat inside the ship. Davits were fit-

ted with sheerpoles to prevent the boat

from swinging in and out. In many cases,

two lines ran from the pole around the

boat, back to a block, and then to a

purchase with the second block on the

ship's caprail. There are variations on this

arrangement; check your plans.

Some builders like to embellish the

boats with in oars, buckets, and rudders

— but it's not really authentic. On real

ships this just wasn't done — they would

all be washed overboard in the first

rough seas.

ones because they sometimes are cut

crossgrain and break at the slightest

touch. If that's the case you can make

your own, either by using yo ur plank

bender on a strip of wood the same size

as the fragile kit davit or by cutting two

halves on reverse grain and gluing them

together.

ANCHORS

Anchors have undergone a lot of modi-

fication and improvement over the years

— so it's important that you find the right

one for your model. Again, a trip to the

library will help. Some kits will supply

woodstock that must be fitted around the

upper portion of the anchor stock. After

gluing the two halves together, you need

metal loops, or something that looks like

metal: Use thread or tape or even strips

made from a sheet of shiny copper. Look

at Figure 65.

Earlier, ships stowed their anchors

outboard, lashing them to chainplates or

to bitts — wooden posts — on the fore-

deck. Later the anchors were stowed

inboard. The anchor was raised to the

water surface by the hawse cable or

chain; then it was raised to the cathead

— a wood or metal beam at the bow —

by, and this makes sense, the cathead

tackle. Another tackle was then secured

to one of the anchor's flukes and the

anchor was hoisted over the bulwarks

to its stowed position and lashed in

place.

DAVITS . Davits will vary with the ship

and the era — some will be wooden,

others metal. Watch out for the wooden

112

FIGURE 65. Anchors — a finishing touch that

deserves special care.

I prefer as much as possible not to paint

a model. The beauty of natural walnut

contrasted with other woods such as

limewood, boxwood, cherry, mahogany,

or ebony is really something to rest your

eyes on.

Avoid shiny finishes for period ship

models: Don't use varnishes or oils, for

they attract dust like a magnet.

To give your model the natural, raw

look of old, use acrylic matte varnishes

(decoupage), which you can find in art

stores. Apply a first coat, let it dry, and

then rub it with a very fine (0000) steel

wool. Apply a second coat and again rub

it with a very fine steel wool. If your

model is a more modern craft you can

use acrylic gloss medium and varnish.

These varnishes can also be used

over acrylic base paint for a deeper tone

and protection.

Preparing the surface of the wood

will lead to better results. If you decide

to paint, apply a coat of acrylic model-

ing paste with a stiff nylon brush until it

is smooth. Be careful here — the paste

dries hard, like fiberglass, and sanding

off rough spots is a tough job. But paint-

ing over a surface treated with this paste

is a blessing; it can be sanded eggshell

smooth, and it prevents the paint from

showing the wood grain.

Use water-soluble acrylic-base

paints. There are no vapors, no streaks,

and no messy brush cleaning. If you have

to use petroleum-base paints, confine

them to metal or very small areas. This

kind of paint dries too quickly and is

FINISHING AND PAINTING

Depending on the period and style, you

can leave your model in natural wood

or you can paint it. Or you can do some-

thing in between — leaving it natural

above the waterline and painted below.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: