bird_bag - torebka ptak - opis wykonania, szablony.pdf
(
467 KB
)
Pobierz
lintu_kaikki.FH11
BIRD BAG
Height of body
of bag 18 cm
PATTERN PIECES
cut
Corduroy (exterior)
1
side panel
2
Green cotton fabric (lining)
1
side panel
2
Patterned cotton fabric
3
wing (pocket)
2+2
18 cm
Fusible wadding
1
side panel
2
3
wing
2
SMALL-SCALE PATTERN PIECES
exterior
MATERIALS
- 20 cm corduroy for bag exterior
- piece of green cotton fabric for lining, piping strips
and frills
- piece of patterned cotton fabric for pockets, legs
and shoulder strap
- fusible wadding, Vlieseline Volumenvlies H 640
- 120 cm cotton cord, ø 5 mm
- sew-on snap fastener, ø 10 mm
lining
outer edges together. Leave small opening at bottom edge
of each wing for turning it right side out. Trim seam allowances
and turn wings right side out. Topstitch top edge of wing
(=opening edge of pocket). Pin wings to exterior side panels
as marked on pattern and topstitch them in place close to
edge, closing openings at the same time.
Legs:
Pin leg pieces together in pairs, right sides facing, and
stitch them together, leaving straight top edge of each leg
open. Trim seam allowances, clip into corner on each leg and
turn legs right side out. Machine-baste legs to exterior side
panels as marked on pattern.
Shoulder strap:
Fold shoulder strap piece in half lengthwise,
right sides together, and stitch its long edge. Turn shoulder
strap right side out and press it flat carefully, placing seam
in the middle of strap. Lay cotton cord in the middle of
shoulder strap, with its ends at equal distance from each end
of strap. Fold and pin shoulder strap in half lengthwise,
enclosing cord within strap. Topstitch edges of shoulder strap
together along length of cord. Stitch across shoulder strap
at each end of cord to stop cord from slipping out. Pin and
machine-baste open ends of shoulder strap to one of the
exterior side panels as marked on pattern.
Joining bag exterior:
Pin one edge of exterior base panel
to exterior side panel and stitch panels together along
machine-basting that attaches piping to side panel. Pin and
stitch other side panel to base and side panel section in the
same way, starting and finishing stitching at point marked
with * (asterisk) on pattern (stitching runs across shoulder
strap on each side).
Joining lining:
Stitch lining base panel to one of the lining
side panels. Pin and stitch other side panel to base and side
panel section in the same way, stitching as far as point marked
with * (asterisk) on pattern on tail side. Leave 7 cm opening
at bottom edge of lining for turning bag right side out.
Joining bag exterior and lining:
At this stage, bag exterior
and lining are inside out. Pin and stitch open edges of bag
exterior and lining together, right sides facing. Press seams
at bag opening open with point of iron and turn bag right
side out through opening at bottom edge of lining.
Finishing:
Place lining inside bag exterior and topstitch bag
opening close to edge. Stitch bird’s eye with short zigzag as
marked on pattern. Sew snap fastener at bag opening by hand.
copyright
©
STUDIO TUUMAT OY
OTTOBRE design® FINLAND
INFO:
ottobre@ottobre.fi
SEWING
Seams:
Stitch seams with straight stitch and topstitch them
close to edge.
Preparation:
Pin wadding pieces to exterior side and base
panels as well as in the middle of shoulder strap, to their
wrong side, and fuse them in place. Stitch darts on both
exterior and lining side panels.
Piping:
Fold piping strip in half, wrong sides together. Cut
65 cm piece from cotton cord. Place cord within piping strip
and machine-baste open edges of piping strip together as
close to cord as possible, using zipper foot. Cut piping strip
in half. Machine-baste piping strips to bottom edges of exterior
side panels as marked on pattern.
Pockets:
Finish one long edge of each frill strip with serger
rolled hem or with narrow, short zigzag. Sew gathering
stitches along other long edge of each frill strip. Gather frill
strips to match bottom edges of wings (see pattern markings).
Pin and machine-baste frills to bottom edges of two opposite
wing panels, right sides together, gradually tapering off ends
of frills so that outer edges of frills appear curved. Pin wing
panels together in pairs, right sides facing, and stitch their
2
base of bag
1
2
base of bag
1
4
leg
4
2
base of bag
1
CUTTING
Cut pattern pieces out from pattern sheet. Trace pattern
piece for lining side panel from pattern for exterior side
panel following pattern markings; see also small-scale pattern
pieces.
Cut bag pieces from fabrics and fusible wadding as indicated
on list of pattern pieces. Add 1 cm seam allowances to edges
of pieces cut from fabrics; cut wadding pieces without seam
allowances.
Cut also: (measurements include 1 cm seam
allowances)
From green cotton fabric
- two 3 cm x 17 cm strips for frills on pockets
- 3.5 cm x 65 cm strip for piping
From patterned cotton fabric
- 7 cm x 74 cm strip for shoulder strap
From wadding
- 2.5 cm x 74 cm strip for shoulder strap
All material contained in this OTTOBRE design®
pattern is protected under the Copyright Act.
No material may be reproduced in whole or in
part. All commercial use is strictly forbidden.
All rights reserved to the copyright holder.
LEG -
JALKA -
BEIN -
BEEN -
FOT
frill
frilla
Zierrüschen
ruche
volangremsa
copyright
©
STUDIO TUUMAT OY
OTTOBRE design® FINLAND
INFO:
ottobre@ottobre.fi
All material contained in this OTTOBRE design®
pattern is protected under the Copyright Act.
No material may be reproduced in whole or in
part. All commercial use is strictly forbidden.
All rights reserved to the copyright holder.
li
copyright
©
STUDIO TUUMAT OY
OTTOBRE design® FINLAND
INFO:
ottobre@ottobre.fi
Plik z chomika:
gosia286
Inne pliki z tego folderu:
Torebki dla Blixniaczek. 1jpg.jpg
(129 KB)
Torebki dla Blixniaczek.jpg
(106 KB)
torebka z motywem Hello Kitti.jpg
(66 KB)
torebka z Hello Kitti.jpg
(51 KB)
lehmapussukka_en- cow purse - krówka szablon.pdf
(70 KB)
Inne foldery tego chomika:
■Czapki, kaszkiety
■Kołnierzyki
❢ PRZEGLĄD WYKROJÓW ❢
Bluzki i bluzeczki
Bransoletki z muliny
Zgłoś jeśli
naruszono regulamin