sinamics s120 FH1.pdf

SINAMICS S120

SINAMICS S120 Drive functions

Function Manual · 10/2008

SINAMICS

Foreword

______________

Infeed

______________

Extended setpoint channel

SINAMICS

______________

Servo control

S120

Drive functions

______________

Vector control

Vector V/f control (r0108.2 =

______________

Function Manual

______________

Basic functions

______________

Function modules

Monitoring and protective

functions

______________

Safety Integrated basic

functions

______________

Communication PROFIBUS

DP/PROFINET IO

______________

Applications

Basic information about the

drive system

______________

Appendix

Applies to:

Firmware version 2.6 SP1

(FH1), 10/2008

6SL3097-2AB00-0BP5

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.

CAUTION

without a safety alert symbol, indicates that property damage can result if proper precautions are not taken.

NOTICE

indicates that an unintended result or situation can occur if the corresponding information is not taken into

account.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The device/system may only be set up and used in conjunction with this documentation. Commissioning and

operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes

in this documentation qualified persons are defined as persons who are authorized to commission, ground and

label devices, systems and circuits in accordance with established safety practices and standards.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be adhered to. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this

publication may be trademarks whose use by third parties for their own purposes could violate the rights of the

owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

Siemens AG

Industry Sector

Postfach 48 48

90026 NÜRNBERG

GERMANY

Ordernumber: 6SL3097-2AB00-0BP5

Ⓟ 12/2008

2008.

Technical data subject to change

Foreword

SINAMICS documentation

The SINAMICS documentation is organized in 2 parts:

● General documentation / Catalogs

● Manufacturer / Service documentation

A current overview of the documentation in the available languages is provided in the

Internet:

http://www.siemens.com/motioncontrol

Select the menu items "Support" --> "Technical Documentation" --> "Overview of

Publications."

The Internet version of DOConCD (DOConWEB) is available on the Internet:

http://www.automation.siemens.com/doconweb

Information on the range of training courses and FAQs (Frequently Asked Questions) is

available on the Internet:

http://www.siemens.com/motioncontrol

Follow the menu item "Support".

Usage phases and their tools/documents (as an example)

Table 1

Usage phases and the available documents/tools

Usage phase

Document/tool

Orientation

SINAMICS S Sales Documentation

Planning/configuration

• SIZER configuration tool

• Configuration Manuals, Motors

Decision/ordering

SINAMICS S Catalogs

• SINAMICS S110 Equipment Manual

• SINAMICS S120 Equipment Manual for Control Units and

Additional System Components

• SINAMICS S120 Equipment Manual for Booksize Power

Units

• SINAMICS S120 Equipment Manual for Booksize Compact

Power Units

• SINAMICS S120 Equipment Manual for Chassis Power

Units

• SINAMICS S120 Equipment Manual for AC Drives

Installation/assembly

Drive functions

Function Manual, (FH1), 10/2008, 6SL3097-2AB00-0BP5

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: