LEVEL 2 Ver. 1.1.pdf

DSC-HX1

SERVICE MANUAL

LEVEL 2

US Model

Canadian Model

AEP Model

UK Model

E Model

Australian Model

Hong Kong Model

Chinese Model

Korea Model

Argentine Model

Japanese Model

Tourist Model

Ver. 1.1 2009.04

Revision History

Internal memory

ON BOARD

Revised-1

Replacement of the previously issued

SERVICE MANUAL 9-852-686-31

with this manual.

Link

SPECIFICATIONS

BLOCK DIAGRAMS

PRINTED WIRING BOARDS

SERVICE NOTE

FRAME SCHEMATIC DIAGRAM

REPAIR PARTS LIST

DISASSEMBLY

SCHEMATIC DIAGRAMS

• Precautions on Replacing the SY-218 Board

The components identified by

mark 0 or dotted line with

mark 0 are critical for safety.

Replace only with part num-

ber specified.

Les composants identifiés par une

marque 0 sont critiques pour la

sécurité.

Ne les remplacer que par une pièce

portant le numéro spécifié.

DIGITAL STILL CAMERA

DSC-HX1_L2

2009D0500-1

Published by Kohda TEC

9-852-686-32

Sony EMCS Co.

Link

SPECIFICATIONS

Camera

[System]

Image device: 7.63 mm (1/2.4 type) Exmor

CMOS sensor

Total pixel number of camera:

Approx. 10.3 Megapixels

Effective pixel number of camera:

Approx. 9.1 Megapixels

Lens: G-series 20× zoom lens

f = 5.0 mm – 100.0 mm (28 mm – 560 mm

(35 mm film equivalent))

F2.8 (W) – F5.2 (T)

Shooting movies (16:9): 31 mm – 620 mm

Shooting movies (4:3): 38 mm – 760 mm

Exposure control: Automatic exposure, Shutter

speed priority, Aperture priority, Manual

exposure, Scene selection (10 modes)

White balance: Automatic, Daylight, Cloudy,

Fluorescent 1,2,3, Incandescent, Flash, One

push

File format (DCF compliant):

Still images: JPEG (DCF Ver. 2.0, Exif

Ver. 2.21, MPF Baseline) compliant, DPOF

compatible

Movies: MPEG-4 AVC/H.264 compliant

(stereo)

Recording media: Internal Memory

(approx. 11 MB), “Memory Stick Duo” media

Flash: Flash range (ISO sensitivity

(Recommended Exposure Index) set to Auto):

Approx. 0.3 m to 9.2 m (11 7/8 inches to

30 feet 21/4 inches) (W)/

approx. 1.5 m to 5.1 m (4 feet 11 1/8 inches to

16 feet 87/8 inches) (T)

Viewfinder: Electric view finder (color)

[Input and Output connectors]

Multi use terminal Type2d: (AV-out(SD/HD

Component)/HDMI/USB)

Video output

Audio output (stereo)

HDMI output

USB communication

USB communication:

Hi-Speed USB (USB 2.0 compliant)

[LCD screen]

LCD panel: 7.5 cm (3.0 type) TFT drive

Total number of dots: 230 400 (960 × 240) dots

[Finder]

Panel: 0.5 cm (0.2 type)

Total number of dots:

Approx. 201 000 dots equivalent

[Power, general]

Power: Rechargeable battery pack

NP-FH50, 6.8 V

Power consumption (during shooting, LCD screen

on): 1.2 W

Operating temperature: 0 ˚C to 40 ˚C (32 ˚F to

104 ˚F)

Storage temperature: –20 ˚C to +60 ˚C (–4 ˚F to

+140 ˚F)

Dimensions:

114.5 × 82.8 × 91.8 mm (4 5/8 × 3 3/8 ×

35/8 inches) (W/H/D, excluding protrusions)

Mass (including NP-FH50 battery pack and

“Memory Stick Duo” media):

Approx. 504 g (1lb 1.8 oz)

Microphone: Stereo

Speaker: Monaural

Exif Print: Compatible

PRINT Image Matching III: Compatible

PictBridge: Compatible

BC-VH1 battery charger

Power requirements: AC 100 V to 240 V,

50 Hz/60 Hz, 4 W

Output voltage: DC 8.4 V, 0.28 A

Operating temperature: 0 ˚C to 40 ˚C (32 ˚F to

104 ˚F)

Storage temperature: –20 ˚C to +60 ˚C (– 4 ˚F to

+140 ˚F)

Dimensions: Approx. 60 × 25 × 95 mm

(2 3/8 × 1 × 3 3/4 inches) (W/H/D)

Mass: Approx. 75 g (2.6 oz)

Rechargeable battery pack

NP-FH50

Used battery: Lithium-ion battery

Maximum voltage: DC 8.4 V

Nominal voltage: DC 6.8 V

Maximum charge current: 1.75 A

Maximum charge voltage: DC 8.4 V

Capacity:

typical: 6.1 Wh (900 mAh)

minimum: 5.9 Wh (870 mAh)

Design and specifications are subject to

change without notice.

DSC-HX1_L2

— 2 —

ENGLISH

JAPANESE

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

Dispose of used batteries according to the instructions.

SAFETY-RELATED COMPONENT WARNING!!

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES

DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT

CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE

REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY

DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH

MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS

LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE

COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS

APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS

PUBLISHED BY SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

1. Check the area of your repair for unsoldered or poorly-soldered

connections. Check the entire board surface for solder splashes

and bridges.

2. Check the interboard wiring to ensure that no wires are

“pinched” or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly

transistors, that were installed during a previous repair. Point

them out to the customer and recommend their replacement.

4. Look for parts which, through functioning, show obvious signs

of deterioration. Point them out to the customer and

recommend their replacement.

5. Check the B+ voltage to see it is at the values specified.

6. Flexible Circuit Board Repairing

•Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Unleaded solder

Boards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size.)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40

C higher than

ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350

Caution: The printed pattern (copper foil) may peel away if the

heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than

ordinary solder so use caution not to let solder bridges occur such

as on IC pins, etc.

•Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

DSC-HX1_L2

— 3 —

ENGLISH

JAPANESE

ENGLISH

JAPANESE

஫ҙ

ి஑ͷަ׵͸ɼਖ਼͘͠ߦΘͳ͍ͱഁ྾͢ΔڪΕ͕͋Γ·͢ɻ

ి஑Λަ׵͢Δ৔߹ʹ͸ඞͣಉ͡ܕ໊ͷి஑ຢ͸ಉ౳඼ͱަ׵

͍ͯͩ͘͠͞ɻ

࢖༻ࡁΈి஑͸ɼऔѻࢦࣔʹैͬͯॲ෼͍ͯͩ͘͠͞ɻ

αʔϏεɼ఺ݕ࣌ʹ͸࣍ͷ͜ͱʹ͝஫ҙԼ͍͞ɻ

஫ҙࣄ߲Λ͓कΓ͍ͩ͘͞ɻ

αʔϏεͷͱ͖ಛʹ஫ҙΛཁ͢Δݸॴʹ͍ͭͯ͸ɼ

ΩϟϏωοτɼγϟʔγɼ෦඼ͳͲʹϥϕϧ΍ೀҹͰ

஫ҙࣄ߲Λද͍ࣔͯ͠·͢ɻ͜ΕΒͷ஫ҙॻ͖ٴͼऔ

ѻઆ໌ॻ౳ͷ஫ҙࣄ߲Λඞ͓ͣकΓԼ͍͞ɻ

ࢦఆ෦඼ͷ͝࢖༻Λ

ηοτͷ෦඼͸೉೩ੑ΍଱ిѹͳͲ҆શ্ͷಛੑΛ

࣋ͬͨ΋ͷͱͳ͍ͬͯ·͢ɻैͬͯަ׵෦඼͸ɼ࢖༻

͞Ε͍ͯͨ΋ͷͱಉ͡ಛੑͷ෦඼Λ࢖༻ͯ͠Լ͍͞ɻ

ಛʹճ࿏ਤɼ෦඼දʹ0ҹͰࢦఆ͞Ε͍ͯΔ҆શ্ॏཁ

ͳ෦඼͸ඞͣࢦఆͷ΋ͷΛ͝࢖༻Լ͍͞ɻ

෦඼ͷऔ෇͚΍഑ઢͷҾ͖·Θ͠͸΋ͱͲ͓Γʹ

҆શ্ɼνϡʔϒ΍ςʔϓͳͲͷઈԑࡐྉΛ࢖༻ͨ͠

ΓɼϓϦϯτج൘͔Βු͔ͯ͠औ෇͚ͨ෦඼͕͋Γ·

͢ɻ·ͨ಺෦഑ઢ͸Ҿ͖·Θ͠΍ΫϥϯύʹΑͬͯൃ

೤෦඼΍ߴѹ෦඼ʹ઀ۙ͠ͳ͍Α͏഑ྀ͞Ε͍ͯ·͢

ͷͰɼ͜ΕΒ͸ඞͣ΋ͱͲ͓Γʹͯ͠Լ͍͞ɻ

αʔϏεޙ͸҆શ఺ݕΛ

αʔϏεͷͨΊʹऔ֎ͨ͠ωδɼ෦඼ɼ഑ઢ͕΋ͱͲ

͓Γʹͳ͍ͬͯΔ͔ɼ·ͨαʔϏεͨ͠ݸॴͷपลΛ

ྼԽͤͯ͞͠·ͬͨͱ͜Ζ͕ͳ͍͔ͳͲΛ఺ݕ͠ɼ҆

શੑ͕֬อ͞Ε͍ͯΔ͜ͱΛ֬ೝͯ͠Լ͍͞ɻ

νοϓ෦඼ަ׵࣌ͷ஫ҙ

•

ϑϨΩγϒϧϓϦϯτج൘ͷऔѻ͍ʹ͍ͭͯ

•

ίςઌԹ౓Λˆલޙʹͯ͠ߦͳͬͯԼ͍͞ɻ

•

ಉҰύλʔϯʹԿ౓΋ίςઌΛ౰ͯͳ͍ͰԼ͍͞ɻ

ʢճҎ಺ʣ

ύλʔϯʹྗ͕ՃΘΒͳ͍Α͏஫ҙͯ͠Լ͍͞ɻ

ແԖ൒ాʹ͍ͭͯ

ແԖ൒ాΛ࢖༻͍ͯ͠Δج൘ʹ͸ɼແԖʢ-FBE'SFFʣΛҙ

ຯ͢ΔϨουϑϦʔϚʔΫ͕ϓϦϯτ͞Ε͍ͯ·͢ɻ

ʢ஫ҙɿج൘αΠζʹΑͬͯ͸ɼແԖ൒ాΛ࢖༻ͯ͠

͍ͯ΋ϨουϑϦʔϚʔΫ͕ϓϦϯτ͞Εͯ

͍ͳ͍΋ͷ͕͋Γ·͢ʣ

ɿϨουϑϦʔϚʔΫ

ແԖ൒ాʹ͸ɼҎԼͷಛੑ͕͋Γ·͢ɻ

•

༥఺͕ैདྷͷ൒ాΑΓ΋໿ˆߴ͍ɻ

ैདྷͷ൒ాͯ͜Λͦͷ··࢖༻͢Δ͜ͱ͸ՄೳͰ͢

͕ɼগ͠௕Ίʹͯ͜Λ౰ͯΔඞཁ͕͋Γ·͢ɻ

Թ౓ௐઅػೳͷ͍ͭͨ൒ాͯ͜Λ࢖༻͢Δ৔߹ɼ໿

ˆʹઃఆͯ͠Լ͍͞ɻ

஫ҙɿ൒ాͯ͜Λ௕͘౰ͯ͗͢Δͱɼج൘ͷύλʔ

ϯʢಔഩʣ͕͸͕Εͯ͠·͏͜ͱ͕͋Γ·͢

ͷͰɼ஫ҙͯ͠Լ͍͞ɻ

•

೪ੑ͕ڧ͍

ैདྷͷ൒ాΑΓ΋೪ੑ͕ڧ͍ͨΊɼ*$୺ࢠͳͲ͕൒ా

ϒϦοδ͠ͳ͍Α͏ʹ஫ҙͯ͠Լ͍͞ɻ

औ֎ͨ͠෦඼͸࠶࢖༻͠ͳ͍ͰԼ͍͞ɻ

• λϯλϧίϯσϯαͷϚΠφεଆ͸೤ʹऑ͍ͨΊަ

׵࣌͸஫ҙͯ͠Լ͍͞ɻ

•

ैདྷͷ൒ాͱࠞͥͯ࢖༻Մೳ

ແԖ൒ాʹ͸ແԖ൒ాΛ௥Ճ͢Δͷ͕࠷దͰ͕͢ɼ

ैདྷͷ൒ాΛ௥Ճͯ͠΋ߏ͍·ͤΜɻ

DSC-HX1_L2

— 4 —

ENGLISH

JAPANESE

1. SERVICE NOTE

ENGLISH

JAPANESE

1-1. PRECAUTION ON REPLACING THE SY-218 BOARD

Restore Data

When you replace to the repairing board, get the acquire data from the former needed for the adjustment from.

Start the Adjust Manual in the Adjust Station and perform “Restore Data” to get the data.

The data getting for this model is as follows.

•

Note: When you cannot read data from the former replace the same time SY-218 board and lens.

Destination Data

When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.

Start the Adjust Manual in the Adjust Station and execute the “Destination Data Write”.

USB Serial No.

The set is shipped with a unique ID (USB Serial No.) written in it.

This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.

Start the Adjust Manual in the Adjust Station and execute the “USB Serial No. Input”.

Angular Velocity Sensor

When you replace to the repairing board, write down the sensitivity displayed on the angular velocity sensor (SE401, SE402).

Start the Adjust Manual in the Adjust Station and execute the “Angular Velocity Sensor Sensitivity Adjustment”, input the data written down.

SY-218 BOARD (SIDE B)

YY : YAW sensor sensitivity

SE401

PP : PITCH sensor sensitivity

Note: The sensor sensitivity of SE401, SE402 of SY-218 board are written only repair parts.

1-2. PRECAUTION ON REPLACING THE LENS

When replacing the lens, write down the wide limit data given on

the lens for service.

Start the Adjust Manual in the Adjust Station and execute the “Wide

Limit Adjustment”, input the data written down.

Wide Limit Data (2-byte data)

XX XX

Note: The wide limit data of lens is written only repair parts.

DSC-HX1_L2

1-1

ENGLISH

JAPANESE

USB Serial No.

• Angular Velocity Sensor Sensitivity Adjustment (Dp/Dy Data)

• Wide Limit Adjustment

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: