flufall.pdf

(97 KB) Pobierz
5705908 UNPDF
Fluffy by Marc Kirschenbaum (NY)
©1994
Complex
An 18" square makes a model 6" high
1.With darker side up, form
rabbit ears on both sides.
2.Swing back.
3.Valley up.
3-5
4.Valley down.
5.Unfold.
6.Repeat steps 3-5 in mirror
image.
7.Asymmetrical squash.
8.Squash.
9.Pull out single layer to make
symetrical.
5705908.016.png
10.Squash.
11.Valley up.
12.Precrease.
13.Form valley fold, allowing
squash to form at bottom.
14.Pull one layer through.
15.Valley folds.
16.Turn over.
17.Swing down.
18.Open out top.
19.Collapse into rabbit-ear
formation.
20.Squash.
21.Sink halfway.
5705908.017.png 5705908.018.png 5705908.019.png 5705908.001.png 5705908.002.png 5705908.003.png 5705908.004.png
22.Swing over.
23.Petal up.
24.Swing up.
25.Sink triangularly.
26.Swing down.
27.Valley outwards.
28.Precrease flap halfway.
29.Valley along precrease.
30.Valley down point, while
swinging out top single layer.
Edge B
Flap A
31.Swing over flap A, while
incorporating a reverse fold.
A gusset will form where flap
A meets the point.
32.Pull up the thick set of layers
33.Pull up edge B, so that it is
parallel with the base of
model.
5705908.005.png
1/2
22-33
34.Repeat steps 22-33 on the
other side.
35. Valley. Rotate model.
36.Squash.
37.Valley up.
38.Mountain fold the single layer
to match up with folded edge
above.
39.Pull out single layer from
underneath.
36-37,39-40
3-5
40.Swing over. Repeat steps
36-40 on other side, skipping
step 38.
41.Repeat steps 3-5 on the top
flap.
42.Top shown only. Fold in half,
while outside reverse folding.
44
43.Reverse fold.
44.Pull around single layer from
underneath.
45.Repeat step 44 behind (it is
easier to first swing the small
flap to the other side to
accomplish this).
5705908.006.png
Point A
Point B
46.Swing one flap over.
47.Valley up; see next step for
positioning.
48.Note that points A and B are
on the same plane. Swing
over.
49.Swing over.
50.Fold out top edges a small
amount, allowing tip to
squash.
51.Swing over head while
swiveling out the ear. Form
mountan fold first. Center of
ear should lie at 45 angle.
49-52
52.Mountain edge of ear to
make it symetrical. Repeat
steps 49-52 on other side.
53.Turn over.
54.Fold sides in. Pull out tiny
flap from bottom pocket.
55.Pull single layer to surface
(closed sink).
56.Stretch the bottom upwards.
Valley the lower edges of the
leds to the center.
57.Swivel the material from the
legs behind.
5705908.007.png 5705908.008.png 5705908.009.png 5705908.010.png 5705908.011.png 5705908.012.png 5705908.013.png 5705908.014.png 5705908.015.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin