TDA1074A.PDF

(167 KB) Pobierz
11046387 UNPDF
INTEGRATED CIRCUITS
DATA SHEET
TDA1074A
Dual tandem electronic
potentiometer circuit
Product specification
File under Integrated Circuits, IC01
December 1982
11046387.003.png
Philips Semiconductors
Product specification
Dual tandem electronic
potentiometer circuit
TDA1074A
GENERAL DESCRIPTION
The TDA1074A is a monolithic integrated circuit designed for use as volume and tone control circuit in stereo amplifiers.
This dual tandem potentiometer IC consists of two ganged pairs of electronic potentiometers with the eight inputs
connected via impedance converters, and the four outputs driving individual operational amplifiers. The setting of each
electronic potentiometer pair is controlled by an individual d.c. control voltage. The potentiometers operate by current
division between the arms of cross-coupled long-tailed pairs. The current division factor is determined by the level and
polarity of the d.c. control voltage with respect to an externally available reference level of half the supply voltage. Since
the electronic potentiometers are adjusted by a d.c. control voltage, each pair can be controlled by single linear
potentiometers which can be located in any position dictated by the equipment styling. Since the input feedback
impedances around the operational amplifier gain blocks are external, the TDA1074A can perform bass/treble and
volume/loudness control. It also can be used as a low-level fader to control the sound distribution between the front and
rear loudspeakers in car radio installations.
Features
·
High impedance inputs to both ‘ends’ of each electronic potentiometer
·
Ganged potentiometers track within 0,5 dB
·
Electronic rejection of supply ripple
·
Internally generated reference level available externally so that the control voltage can be made to swing positively
and negatively around a well-defined 0 V level
·
The operational amplifiers have push-pull outputs for wide voltage swing and low current consumption
·
The operational amplifier outputs are current limited to provide output short-circuit protection
·
Although designed to operate from a 20 V supply (giving a maximum input and output signal level of 6 V), the
TDA1074A can work from a supply as low as 7,5 V with reduced input and output signal levels.
QUICK REFERENCE DATA
Supply voltage (pin 11)
V P
typ.
20 V
Supply current (pin 11)
I P
typ.
22 mA
Input signal voltage (r.m.s. value)
V i(rms)
max.
6 V
Output signal voltage (r.m.s. value)
V o(rms)
max.
6 V
Total harmonic distortion
THD
typ.
0,05 %
Output noise voltage (r.m.s. value)
V no(rms)
typ.
50
m
V
Control range
Da
typ.
110 dB
Cross-talk attenuation (L/R)
a ct
typ.
80 dB
Ripple rejection (100 Hz)
a 100
typ.
46 dB
Tracking of ganged potentiometers
D G v
typ.
0,5 dB
Supply voltage range
V P
7,5 to 23 V
Operating ambient temperature range
T amb
-
30 to + 80
°
C
PACKAGE OUTLINE
18-lead DIL; plastic (SOT102); SOT102-1; 1996 July 18.
December 1982
2
11046387.004.png 11046387.005.png
Philips Semiconductors
Product specification
Dual tandem electronic
potentiometer circuit
TDA1074A
V P /2 at pin 8;
Z1 = Z2 = Z3 = Z4 = 22 k W ; the input generator resistance R G = 60 W ; the output load resistance
R L = 4,7 k
W
; the coupling capacitors at the inputs and outputs are C i = 2,2
m
F and C o = 10
m
F
respectively.
December 1982
3
Fig.1 Block diagram and basic external components; I c1 (at pin 9) and I c2 (at pin 10) are control input currents;
V c1 (at pin 9) and V c2 (at pin 10) are control input voltages with respect to V ref =
11046387.006.png
Philips Semiconductors
Product specification
Dual tandem electronic
potentiometer circuit
TDA1074A
RATINGS
Limiting values in accordance with the Absolute Maximum System (IEC 134)
Supply voltage (pin 11)
V P
max.
23 V
Control voltages (pins 9 and 10)
±
V c1 ;
±
V c2
max.
1 V
Input voltage ranges (with respect to pin 18)
at pins 3, 4, 5, 6, 13, 14, 15, 16
V i
0 to V P V
Total power dissipation
P tot
max.
800 mW
Storage temperature range
T stg
-
55 to + 150
C
Operating ambient temperature range
T amb
- 30 to + 80
° C
THERMAL RESISTANCE
From crystal to ambient
R th cr-a
=
80 K/W
REMARK
The difference between the TDA1074 and its successor the TDA1074A is shown in Fig.2 as the different component
configuration at pin 8.
Fig.2 Component configuration at pin 8 showing the difference between the TDA1074 and the TDA1074A.
December 1982
4
°
11046387.001.png
Philips Semiconductors
Product specification
Dual tandem electronic
potentiometer circuit
TDA1074A
APPLICATION INFORMATION
Treble and bass control circuit
V P =
25
°
C; measured in Fig.3; R G =
60
W
; R L >
4,7 k
W
; C L <
30 pF; f
=
1 kHz; with a linear frequency
response (V c1 =
V c2 =
0 V); unless otherwise specified
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
Supply current (without load)
I P
14
22
30
mA
Frequency response ( - 1 dB)
V c1 = V c2 = 0 V
f
10
-
20 000
Hz
Voltage gain at linear frequency
response (V c1 = V c2 = 0 V)
G v (1)
-
0
-
dB
Gain variation at f = 1 kHz
at maximum bass/treble boost or
cut at
V c1 =
±
V c2 = 120 mV
D
G v (1)
-
±
1
-
dB
Bass boost at 40 Hz (ref. 1 kHz)
V c2 = 120 mV
-
17,5
-
dB
Bass cut at 40 Hz (ref. 1 kHz)
- V c2 = 120 mV
-
17,5
-
dB
Treble boost at 16 kHz (ref. 1 kHz)
V c1 = 120 mV
-
16
-
dB
Treble cut at 16 kHz (ref. 1 kHz)
-
-
16
-
dB
Total harmonic distortion
at V o(rms) = 300 mV
f = 1 kHz (measured selectively)
THD
-
0,002
-
%
f = 20 Hz to 20 kHz
THD
-
0,005
-
%
at V o(rms) = 5 V
f = 1 kHz
THD
-
0,015
0,1
%
f = 20 Hz to 20 kHz
THD
-
0,05
0,1
%
Signal level at THD = 0,7%
(input and output)
V i; o(rms)
5,5
6,2
-
V
Power bandwidth at reference
level V o(rms) = 5 V (
-
3 dB);
THD = 0,1%
B
-
40
-
kHz
December 1982
5
20 V; T amb =
±
V c1 = 120 mV
11046387.002.png

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin