This "SimpleMouse" Smartcardprogrammer can be used to read and write most of all async - Smartcards (Processorcards), including the new "Hornet and +1" DPSC´s in update and reprogramming mode. It is jumper-selectable in either Smartmouse or Phoenix Mode (Reset active hi or low) and Jumper selectable for 3.57 and 6 MHz The "original" Smartmouse gets its power out of the serial port of the Hostcomputer - in this design this "feature" is not implemented because the Hostcomputer can only deliver about 15 mA to the Programmer. This is not enough for older Smartcards. So this design uses an 9V Alkaline Battery 6LR61. To make this design cheap there are no gimmicks like flashing diodes or expensive connectors and switches. You have to solder the 9 or 25 pin serial cable directly the corresponding pads of the PCB. ++++++++JUMPERS+++++++++ SIP1 is for selecting the Clockrate 3.57 or 6MHz SIP 1 Shorting pin 1 + 2 -> 3.57 MHz Shorting pin 2 + 3 -> 6 MHz SIP2 is for selecting the type of mode (Smartmouse or Phoenix) SIP 2 Shorting pin 1 + 2 -> Smartmouse Shorting pin 2 + 3 -> Phoenix SIP3 SIP3 is a Jumperblock which is used as a "Switch" to turn the Battery on an off - or as the connector for an external DC-powersupply. Shorting pin 1+2 -> Power off Shorting pin 2+3 -> Power on Without Jumper you can connect an external DC-Powersupply to this Header: Pin1 -> GND Pin2 -> 9 to 15 Vdc Pin3 -> left open SIP4 SIP3 is´nt really a Jumperblock it is the connection to the serial Port of the Hostcomputer. SIP4 9Pin SubD Serial port cable Pin1 -> Pin 5 Pin2 -> Pin 2 Pin3 -> Pin 3 Pin4 -> Pin 1 Pin5 -> Pin 7 ++++++++PARTLIST+++++++++ ID Comment BT1 9V Block Alkaline C1 22pF RM 5 Keramik C2 22pF RM 5 Keramik C3 22pF RM 5 Keramik C4 22pF RM 5 Keramik C5 100nF RM 5 KDPU C6 100nF RM 5 KDPU C7 1uF RM 2.5 Tantal C8 1uF RM 2.5 Tantal C9 1uF RM 2.5 Tantal C10 1uF RM 2.5 Tantal C11 1u RM 2.5 Tantal C12 100nF RM 5 KDPU C13 100nF RM 5 KDPU C14 47pF RM 5 Keramik C15 1uF RM 2.5 Tantal D1 BAT41 or BAT48 Shottky!! D2 1N4148 LD1 LED 3mm red Low Power R1 1M RM 5 Bauform 02/04 1/10W R2 2K2 RM 5 Bauform 02/04 1/10W R3 1M RM 5 Bauform 02/04 1/10W R4 2K2 RM 5 Bauform 02/04 1/10W R5 2K2 RM 5 Bauform 02/04 1/10W R6 2K2 RM 5 Bauform 02/04 1/10W R7 10K RM 5 Bauform 02/04 1/10W SC1 Smartcard Adapter Amphenol Switch opens when Card is inserted! SIP1 Jumperblock 3Pin SIP2 Jumperblock 3Pin SIP3 Jumperblock 3Pin SIP4 Jumperblock 5Pin U1 74HC00 U2 MAX 232 U3 78L05 X1 3.57MHz HC18/U X2 6MHz HC18/U All Rs are 1/10W 4mm for laying mount or 1/4 W for standing mount. ++++++REMARKS+++++ It is very important for this design to use a Shottky diode for D1. Any other type will definitely NOT work! Look for the right polarity of the tantalum condensators! The MAX232 includes a so called chargepump and generates positive an negative Voltages respect to ground. So it is possible that the positive pole of an condensator is connected to ground - this is NOT wrong! For Mounting the Battery and fasten the serial cabel drill bigger holes at the corresponding points and use cablestrips. The enclosed Tiff´s have a resolution of 400 dpi. ++++++++++++++++++
smetek