amd101_e.pdf

WIRELESS MAGNETIC DETECTOR

AMD-101

amd101_e 09/05

The AMD-101 wireless magnetic detector is designed for operation as part of the

ABAX two-way wireless system.

The AMD-101 detector is of the NC type, i.e. moving the magnet away from the reed

relay opens the electric circuit, which is recognized as violation of the detector.

Descriptions of Figure 1:

1 – additional input terminals - The NC type detector can be

connected to them. The signal from the additional input

is passed independently, the AMD-101 detector is

included twice in the list of wireless devices in the

system.

2 – tamper contact – It reacts to opening or pull-off of the

housing from the wall.

3 – CR123A lithium battery (voltage: 3V), which ensures

approx. two years’ operation.

4 – reed switch 1.

5 – reed switch 2.

6 – pins which enables to choose the active reed switch.

Fig. 1. View of the

detector PCB.

active reed switch 1

active reed switch 2

Fig. 2. The way of putting jumper on pins.

7 – LED indicator – is on in the T EST MODE only (see the ACU-100 controller manual)

to signal communication with the controller and violation (of the detector or

tamper contact).

Placed on the electronics board is a label with 7-digit serial number, which must be

indicated when registering the detector in the system.

1. D ETECTOR INSTALLATION

Prior to permanent mounting of the detector, you should check the level of

signal received from the detector by the ACU-100 controller and, if necessary,

change place of the installation so as to ensure optimal positioning in terms of

communication.

Place the battery inside the detector immediately before registering the detector

in the controller. If not registered or lacking communication with the controller,

the detector consumes more energy, which reduces the battery lifetime.

Be particularly careful when installing or replacing the battery, so as not to

damage the reed switches on the electronics board.

SATEL

AMD-101

The cable connecting the additional detector with the onboard terminals may not be

longer than 3m. If the additional input is unused, its contacts should be shorted.

For information on registration and installation of the detector in the wireless system -

see the ACU-100 controller user manual.

Side view

reed switches

tamper contact spring

Top view

17mm

reed switches

110mm

Fig. 3. View of AMD-101 in the housing with indicated position of

reed switches.

magnet

reed switch

20mm

Fig. 4. Examples of mounting reed switch and magnet, showing the maximum ranges

(top view). The indicated ranges apply to the magnet situated at the height of

AMD-101 PCB.

AMD-101

ABAX

2. T ECHNICAL DATA

Detector type .............................................................................................................. NC

Operating frequency band .......................................................... 868.0MHz ÷ 868.6MHz

Additional input sensitivity .................................................................................... 312ms

Power supply .........................................................................lithium battery CR123A 3V

Lifetime of detector power battery .......................................................... approx. 2 years

Operating temperature range ....................................................................... 0°C...+55°C

Dimensions of reed relay housing ........................................................... 24x110x27mm

Batteries in the battery-supplied wireless equipment should be replaced by

qualified personnel. Incorrect replacement of the battery can pose an explosion

hazard.

Always use the CR123A 3V lithium batteries.

The used batteries must not be discarded, but should be disposed of in

accordance with the existing rules for environment protection.

DECLARATION OF CONFORMITY

Manufacturer: SATEL spółka z o.o.

ul. Schuberta 79

80-172 Gdańsk, POLAND

tel. (+48 58) 320-94-00

fax. (+48 58) 320-94-01

Product description : Wireless magnetic detector with an additional input, designed for interaction

with elements of the ABAX wireless system, operating in the 868.0MHz – 868.6MHz frequency

band, supplied from a 3V lithium cell. The device is intended to be used in burglary and panic alarm

systems.

This product conforms to the following EU Directives:

R&TTE 1999/5/EC

This product meets requirements of the harmonized standards:

R&TTE: ETSI EN 300 220-1: v.1.3.1; ETSI EN 300 220-3: v.1.1.1;

EMC: ETSI EN 301 489-1: v.1.5.1.; EN 301 489-3: v.1.4.1

Safety: EN60950-1:2001

Notified body taking part in conformity evaluation:

Identification No.: 1471

Gdańsk, Poland 2005-07-15

Product:

AMD-101 - Wireless Magnetic Detector for

ABAX System

Head of Test Laboratory:

Michał Konarski

The latest EC declaration of conformity and product approval certificates are available for

downloading on website www.satel.pl

SATEL

AMD-101

SATEL sp. z o.o.

ul. Schuberta 79

80-172 Gdańsk

POLAND

tel. + 48 58 320 94 00

info@satel.pl

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: