54ABT652.pdf
(
361 KB
)
Pobierz
August 1998
54ABT652
Octal Transceivers and Registers with TRI-STATE
®
Outputs
General Description
The ’ABT652 consists of bus transceiver circuits with D-type
flip-flops, and control circuitry arranged for multiplexed trans-
mission of data directly from the input bus or from the inter-
nal registers. Data on the A or B bus will be clocked into the
registers as the appropriate clock
pin go
es to HIGH logic
level. Output Enable pins (OEAB, OEBA) are provided to
control the transceiver function.
n
Multiplexed real-time and stored data
n
A and B output sink capability of 48 mA, source
capability of 24 mA
n
Guaranteed latchup protection
n
High impedance glitch free bus loading during entire
power up and power down cycle
n
Nondestructive hot insertion capability
n
Standard Microcircuit Drawing (SMD) 5962-9324201
Features
n
Independent registers for A and B buses
Ordering Code:
Commercial
Package
Package Description
Number
54ABT652J-QML
J24A
24-Lead Ceramic Dual-in-line
54ABT652W-QML
W24C
24-Lead Cerpack
54ABT652E-QML
E28A
28-Lead Ceramic Leadless Chip Carrier, Type C
Connection Diagram
Pin Assignment for
DIP and Flatpack
DS100220-1
TRI-STATE
®
is a registered trademark of National Semiconductor Corporation.
www.national.com
© 1998 National Semiconductor Corporation
DS100220
Connection Diagram
(Continued)
Pin Assignment for LCC
DS100220-48
www.national.com
2
Pin Descriptions
Pin Names
Description
A
0
–A
7
Data Register A Inputs/TRI-STATE Outputs
B
0
–B
7
Data Register B Inputs/TRI-STATE Outputs
CPAB, CPBA
Clock Pulse Inputs
SAB, S
BA
Select Inputs
OEAB, OEBA
Output Enable Inputs
Logic Diagram
DS100220-3
Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays.
Functional Description
In the transceiver mode, data present at the HIGH imped-
ance port may be stored in either the A or B register or both.
The select (SAB, SBA) controls can multiplex stored and
real-time.
The examples in Figure1demonstrate the four fundamental
bus-management functions that can be performed with the
’ABT652C.
Data on the A or B data bus, or both can be stored in the in-
ternal D flip-flop by LOW to HIGH transitions at the appropri-
ate Clock Inputs (CPAB, CPBA) regardless of the Select or
Output Enable Inputs. When SAB and SBA are in the real
time transfer mode, it is also possible to store data without
using the in
ternal
D flip-flops by simultaneously enabling
OEAB and OEBA. In this configuration each Output rein-
forces its Input. Thus when all other data sources to the two
sets of bus lines are in a HIGH impedance state, each set of
bus lines will remain at its last state.
3
www.national.com
Functional Description
(Continued)
Note A: Real-Time
Transfer Bus B to Bus A
Note C: Storage
DS100220-6
DS100220-4
OEAB
OEBA
CPAB
CPBA
SAB
SBA
OEAB
OEBA
CPAB
CPBA
SAB
SBA
X
H
N
X
X
X
L
L
X
X
X
L
L
X
X
N
X
X
L
H
N
N
X
X
Note D: Transfer Storage
Data to A or B
Note B: Real-Time
Transfer Bus A to Bus B
DS100220-7
DS100220-5
OEAB
OEBA
CPAB
CPBA
SAB
SBA
OEAB
OEBA
CPAB
CPBA
SAB
SBA
H
L
HorL
HorL
H
H
H
H
X
X
L
X
FIGURE 1.
www.national.com
4
Functional Description
(Continued)
Inputs
Inputs/Outputs
(Note 1)
Operating Mode
OEAB
OEBA
CPAB
CPBA
SAB
SBA
A
0
thru A
7
B
0
thru B
7
L
H
H or L
H or L
X
X
Input
Input
Isolation
L
H
N
N
X
X
Store A and B Data
X
H
N
H or L
X
X
Input
Not Specified
Store A, Hold B
H
H
N
N
X
X
Input
Output
Store A in Both Registers
L
X
H or L
N
X
X
Not Specified
Input
Hold A, Store B
L
L
N
N
X
X
Output
Input
Store B in Both Registers
L
L
X
X
X
L
Output
Input
Real-Time B Data to A Bus
L
L
X
H or L
X
H
Store B Data to A Bus
H
H
X
X
L
X
Input
Output
Real-Time A Data to B Bus
H
H
H or L
X
H
X
Stored A Data to B Bus
H
L
H or L
H or L
H
H
Output
Output
Stored A Data to B Bus and
Stored B Data to A Bus
H
=
HIGH Voltage Level
L
=
LOW Voltage Level
X
=
Immaterial
N
=
LOW to HIGH Clock Transition
Note 1:
The data output functions may be enabled or disabled by various signals at OEAB or OEBA inputs. Data input functions are always enabled, i.e., data at
the bus pins will be stored on every LOW to HIGH transition on the clock inputs.
5
www.national.com
Plik z chomika:
kojczuch
Inne pliki z tego folderu:
ADC10461.pdf
(333 KB)
ADC10462.pdf
(333 KB)
100301.pdf
(105 KB)
100302.pdf
(106 KB)
100304.pdf
(109 KB)
Inne foldery tego chomika:
ADC
ANALOG
AUDIO
Bt
CCD
Zgłoś jeśli
naruszono regulamin