S2CFull.pdf

Notes on the fuse:

If you are going for all out light weight, consider leaving out

the fuse spar. The side plates are strong enough for anything

in flight, but will not be quite as tough for rough

landings/crashes. Make sure to use 15-30 minute epoxy or

shoogoo for the main parts...5 min and foam CA are not

strongenough, and will crack under the torque.

1° possitive incidence on top wing only

1/8" Lite ply center strut

Connect upper and lower

ailerons with 1/16 carbon

or steel pushrod

All hinging for control surfaces can be packing

tape or actual hinges. I prefer robart hinge

points epoxied in place for the added longivity

and control freeness.

3/8"x3/8" Hardwood motor block

Groove block to fit carbon rod.

If using GWS 350 Drive, mount

block on Carbon rod so that the

prop/drive shaft is in the same

location as shown on plans.

Elevator Servo (HS-56HB Shown)

4mm Carbon Spar

6mm Depron Fuse Rails

Cut a "V" groove

in foam for

spars. Pull spar

through groove

to make round

3/16" zipties

LiPo Battery

Rudder Servo (HS-56HB Shown)

1 0-1 2# f ish line pu ll-pu ll ru dd er c abl es

2100(3s2p)

6mm Depron Wing Saddle

Use Cotterpin to adjust

tension on pull-pull system.

Mount using Dubro EZ Conectors

1/64 ply gear mount plates

Carbon Tail wheel bracket

Hacker B20-15L shown

1/16" wire wheel axel/steering arm

(Bend 90 deg. at the top to form

a control arm. Use clamp on ball

link to attach to rudder control horn)

Molded Carbon Fiber Gear

Aileron Servo (HS-56HB Shown)

1 each wing half

6mm Depron Struts

(Make 2)

6mm Depron Wing Saddle

Motor/Battery Info

Li-Po Pack Area

Vacuum Formed

Wheel Pants

Motor Gearing Prop Battery Amp Draw Thrust

GWS EPS350C DS (6.6:1) GWS 12x6 2s1p Lipo 9.5 17.1 oz.

GWS EPS350C DS (6.6:1) GWS 11x4.7 3s1p Lipo 11.5 24.3 oz.

Hacker B20-26S 4:1 Planetary APC 11x4.7 3s1p LiPo 11 amps 22.1 oz.

Hacker B20-31S 4:1 Planetary APC 11x4.7 3s1p LiPo 7.7 amps 18.6 oz.

Hacker B20-15L 4:1 Planetary APC 11x4.7 3s2p LiPo 19.5 amps 38.5 oz.

Hacker B20-15L 4:1 Planetary APC 11x4.7 2s1p LiPo 10.8 amps 20.6 oz.

Hacker B20-18L 4:1 Planetary APC 11x4.7 3s1p LiPo 11.7 amps 27.7 oz.

Hacker B20-18L 4:1 Planetary APC 12x6 3s2p LiPo 19 amps 36.7 oz.

Razor RZ300 GWS/5.3:1 GWS 11x4.7 2s1p LiPo 8.8 amps 15.7 oz.

Razor RZ300 GWS/5.3:1 GWS 12x6 2s1p LiPo 9.9 amps 18.5 oz.

Razor RZ300 GWS/6.6:1 GWS 11x4.7 3s1p LiPo 12 amps 26 oz.

Razor RZ350 GWS/6.6:1 GWS 12x6 3s1p LiPo 12.4 amps 27 oz.

Razor RZ350 GWS/6.6:1 GWS 11x4.7 3s1p LiPo 8.7 amps 21.2 oz.

Razor MicroHeli v2 GWS/6.6:1 GWS 12x6 3s1p LiPo 8.9 amps 22.8 oz.

PJS 3D 500 Direct APC 10x4.7 3s2p LiPo 16.4 amps 21.9 oz.

PJS 3D 550 Direct APC 10x4.7 3s2p LiPo 13.8 amps 20.7 oz.

HiMax HA2015-3600 GWS/5.3:1 GWS 12x6 3s1p LiPo 8.7 amps 20.5 oz.

HiMax HA2015-3600 GWS/6.6:1 GWS 12x6 3s1p LiPo 6.5 amps 18.5 oz.

HiMax HA2015-4100 GWS/6.6:1 GWS 12x6 3s1p LiPo 11.2 amps 26.4 oz.

HiMax HA2015-4100 GWS/5.3:1 GWS 11x4.7 3s1p LiPo 11.6 amps 25.2 oz.

HiMax HA2015-5400 GWS/6.6:1 GWS 12x6 2s1p LiPo 10.2 amps 17.8 oz.

HiMax HA2025-3236 3.6:1 Planetary APC 11x4.7 3s2p LiPo 14 amps 29.3 oz.

HiMax HA2025-3236 3.6:1 Planetary APC 12x6 3s2p LiPo 17 amps 32.2 oz.

HiMax HA2025-4236 4.3:1 Planetary APC 11x4.7 3s2p Lipo 20.2 amps 38.1 oz.

Hacker B20-15L shown

1/8" Carbon Spar

Cut Control horns from 1/32"

ply or a plastic coffee can lid.

Push/Pull

Pull Pull

Motor stick instilation.

You will need to adjust the position of

the Carbon rod and motor mount for

your motor/gearbox combination. The

carbon rod may be in a diferent

location, that is OK.

Mount Battery Pack

with 1" Velcro strap.

Also use adhesive

Velcro on the side of

fuselage and back of

pack to secure in

place.

Weight

10.5-15.5 oz.

Thrust

24-39 oz.

Radio

4-5 Chanel

Area

380.2 in2

4.0-6.1oz/ft2

WWW.3DFOAMY.COM

Specs:

Pitts S2C 3D

3D Foamy

Designed and Drawn by Levi Jordan

Updated: 02/22/04.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: