le4.doc

(274 KB) Pobierz

MM0703, Lesson 4

Lesson 4

 

CAPACITANCE AND INDUCTANCE

 

 

Task.  The skills and knowledge taught in this lesson are common to all missile repairer tasks.

 

Objectives.  When you have completed this lesson, you should be able to explain what capacitance and inductance are and describe resistive and capacitive circuits and resistive and inductive circuits.

 

Conditions.  You will have this subcourse book and work without supervision.

 

Standard.  You must score at least 70 on the end-of-course examination that covers this lesson and lessons 1, 2, and 3 (answer 27 of the 38 questions correctly).

 

 

CAPACITANCE

 

In mechanical systems, if an elastic body such as a rubber band is stretched, there is little or no opposition during the first moment of movement.  The opposition increases as the rubber band is extended.  If the rubber band is stretched and then fixed in position, the work done in stretching it is stored in the band and is returned when the rubber band is released.  This mechanical property of elastic bodies illustrates the electrical property called capacitance.

 

A capacitor is any two conductors separated by an insulating material.  When a DC voltage is first applied across a capacitor, considering no losses, the current flow is maximum the first instant and then rapidly decreases to zero when the voltage developed across the capacitor equals the applied voltage. Energy was consumed in building up the voltage.  Removal of the applied voltage leaves the capacitor in charged condition, and energy is stored in the capacitor.

 

The conductors mentioned above are called the plates of the capacitor, and the insulating material is called the dielectric.  In figure 4-1A, when the switch(s) is closed, the battery voltage will cause current to flow.  The current flow will be maximum the first instant and will decrease as the voltage across the capacitor builds up.  This is shown in figure 4-1B.  The number of electrons flowing to plate A is equal to the number flowing away from plate B.  The capacitor is fully charged when the difference of potential existing across the plates of the capacitor equals the battery voltage.  At this time, the current through the capacitor is zero.

 

After the capacitor is fully charged, the switch may be opened and the capacitor will remain charged since there is no path for the electrons on plate A to reach plate B.  The electrostatic field exists between the plates because they are two charged bodies.  The electrical energy is stored between the plates.  The direction of an electrostatic field has been arbitrarily stated as the direction a unit positive charge would move if placed in that field.  The electrostatic field of the charged capacitor of figure 4-1 is shown in figure 4-2.

 

95


When a conductor is placed across the plates, the electrons flow from A to B (figure 4-3) returning the capacitor to its uncharged condition.  This discharges the capacitor.

 

 

Figure 4-1.  Charging of a Capacitor.

 


 

Figure 4-2.  Electrostatic Field Within a Capacitor.

 

Figure 4-3.  Discharging of a Capacitor.


 

Measure of Capacitance

 

The ability of a capacitor (C) to store electrical energy is called capacitance.  The unit of capacitance is the farad (f), named for Michael Faraday.  One f is the amount of capacitance that will store 1 coulomb of charge (6.28x1018 electrons) when 1 V is applied.  The farad is a very large unit, so the microfarad (mfd) and picofarad (pfd) are commonly used.  One microfarad equals 10-6 f, and one pfd equals 10-12 fd.  Capacitors in common use range from 1 pfd to several thousand mfd.

 

The relationship between charge (Q), voltage (E), and C may be expressed as:

 

Q = CE,

where

Q = charge in coulombs,

C = capacitance in fd, and

E = voltage in V.

 


This relationship shows that an increase in charge (coulombs) will result from an increase in voltage or capacitance.

 

Physical Characteristics

 

Relative Size of Parts.  The capacitance of a capacitor is determined by its construction.  Capacitance is directly proportional to the area of its plates and inversely proportional to the thickness of the dielectric.  This means that, if the plates were made larger, the capacitance would increase.  If the plates were moved further apart, the capacitance of the capacitor would decrease.

 

Dielectric.  The dielectric also affects capacitance because the energy is stored in the dielectric.  For example, if a certain capacitor using air as the dielectric were immersed in oil, the capacitance would increase to three times as much.  We say that oil has a dielectric constant of 3.  Air has a dielectric constant of 1 and is the standard of comparison.  The relationship of capacitance, area, thickness of dielectric, and dielectric constant is as follows:

 

A = area of plate

k = dielectric constant

t = thickness of dielectric

 

The actual capacitance in pfd is

 

 

where A is in square inches and t is inches.  The constant, 0.2248, in the above equation is necessary to convert from the electrostatic system of measurement (statcoulombs, statvolts, centimeters, etc.) to the more practical system, using such terms as ohms, amperes, coulombs, and inches.

 

The k of some common insulating materials are given below:

 

 

The choice and thickness of the dielectric material determines not only the capacitance but also the voltage rating of the capacitor.  Since it is usually desirable to have relatively large capacitance in a small space, the dielectric is quite thin.  It must have high dielectric strength to avoid puncture by the applied voltage.  Capacitors are commonly rated as to capacitance, working voltage, and peak voltage.  DC working voltage is the maximum DC voltage the capacitor will stand satisfactorily under certain applied conditions (in its normal temperature range).  AC working voltage rating is lower than DC working voltage rating for a given capacitor because the voltage used is the effective line voltage.  For example, a capacitor with an AC working voltage rating of

 


400 V must be able to withstand a peak voltage of 566 V because that is the peak voltage of the 400 VAC.  Peak voltage ratings are generally higher than working voltage since most dielectrics can withstand higher voltages for a short time than they can stand continuously.

 

Series Connection

 

You saw earlier that

 

 

where t represents the thickness of the dielectric.  If the value of t is doubled, the capacitance would be reduced to one half.  Connecting two equal capacitors in series is the equivalent of building one capacitor having a doubled thickness of dielectric.  See figure 4-4.

 

 

Figure 4-4.  Capacitors in Series.

 

When the upper plate of C1 is made negative, the lower plate of C1 must become equally positive.  The same holds true for C2.  Since the upper plate of C2 is connected to the lower plate of C1, these two points are electrically the same and effectively bring the two dielectrics together forming a single capacitor with a doubled thickness of dielectric.  In this series circuit, as in all series circuits, the current flow is the same in all parts of the circuit.  As a result, the same amount of charge will accumulate on each capacitor, thus the voltage is equally divided between the two capacitors.

 

Calculation of total series capacitance becomes more difficult when capacitors of unequal value are connected in series.  In figure 4-4, two capacitors of equal value are connected in series.  By Kirchhoff's law, the sum of the individual voltages must equal the applied voltage.  The current is the same in all parts of the circuit.  Since the current is the same, the charge deposited on each capacitor will be the same (Q=It).  Charge, voltage, and capacitance are related by

 

             

 

This shows that the voltage on a capacitor is directly proportional to the charge and inversely proportional to the capacitance.  The smallest capacitor will have the greatest voltage across it.


Substituting the value Q/C in place of E, in Kirchhoff's law for series circuits (Et = E1 + E2) you get

 

             

Dividing both sides of this equation by Q, you get

 

             

You can use this equation for determining the total series capacitance of any number of capacitors in series.

 

             

You can rearrange equation as follows:

 

             

             

             

This equation is a useful and timesaving device, but may be used only for two capacitors in series.

 

Capacitors are often connected in series to allow their being used in circuits having a higher voltage than that for which they are rated.  For instance, four 500-V, 4-mfd units in series are the equivalent of a single 2,000-V, 1-mfd unit.  Series operation of capacitors of different values should be avoided.  Since all units receive the same amount of charge, the voltage is divided in inverse proportion to the capacitance of each unit.  One thousand V applied to 1 mfd and 4 mfd in series will produce 200 V across the larger capacitor and 800 V across the smaller.  If both were rated at 500 V, the 1-mfd capacitor would promptly break down putting the entire 1,000 V on the 4-mfd capacitor, which would also be punctured.

 

Parallel Connection

 

Two equal capacitors in parallel are the equivalent of a single capacitor having doubled plate area and the same dielectric thickness (figure 4-5).  The total capacitance, therefore, is the sum of the parallel capacitance, while the voltage applied must be no higher than the rating of the individual units.  For any number of parallel capacitors, total capacitance is

 

CT = C1 + C2 + C3 + C4 + ........ + Cn.

 

Capacitive Reactance

 

Since capacitors are used in AC circuits, it is necessary to define the farad in terms of a changing voltage.  When a steady voltage is applied to a capacitor, a momentary charging current flows.  This current ceases almost immediately.

 


 

Figure 4-5.  Capacitors in Parallel.

 

If the voltage were increased or decreased, another momentary flow of current would take place.  If the voltage could be constantly changed, a continuous current would flow.  A more rapidly changing voltage would cause a larger average current.  For a given rate of voltage change, a larger capacitance causes a larger current to flow.  The unit of capacitance (fd) may then be defined in terms of a changing voltage.

 

A capacitor is said to have a capacitance of 1 fd when a change of 1 V per second produces a current of 1 amp.  This can be expressed as the equation,

 

             

 

where Iav is the average current that is forced to flow through a capacitance of C fd by a change of E V in t sec.

 

In figure 4-6, a sine wave has been divided into 4 equal parts along the time base.  The time required for one cycle is 1/f.  The time required for a change of voltage, from zero to Emax, is a quarter cycle, or 1/4f.  If a sine wave of voltage with a peak voltage of Emax and a frequency f is applied across a capacitor of C fd, the average current during a quarter cycle is

 

 

 

Figure 4-6.  Relationship Between Time and Frequency.


In fact, it is true for the entire cycle because each quarter cycle has the same amount of voltage change per second.  This equation should be simplified to eliminate having to work with both average and maximum terms in one operation.  The relationship between average current and maximum current of a sine wave is then

You should recognize 2/p as the familiar 0.637.  Substituting this value for Iav in its equation,

             

Imax = 2pfCEmax

 

Both sides of the above equation are in terms of maximum values and may be changed to effective values, giving

 

I = 2pfCE,

 

which indicates that the current flowing through a capacitor is proportional to the frequency of the applied sine wave and the capacitance.  As in the case of resistive circuits, you find the opposition to the flow of current by dividing the voltage by the current.  Then by equation I = 2pfCE.

             

 

where f (frequency) is the Hz and C is capacitance in farads.  The angular velocity 2pf is often written w (omega), making reactance equal to 1/w C.  This equation shows that capacitive reactance is inversely proportional to both capacitance and frequency.  The manner in which the opposition to current by a capacitor (Xc) changes with frequency is shown in the graph in figure 4-7.  As f increases, Xc decreases along with the vertical axis.  Ohm's Law is applied to capacitive reactance by substituting Xc for R,

             

The capacitive reactance (Xc) is the opposition offered to the flow of the current by a capacitor.  Since the formula for capacitive reactance was found by working with a sinusoidal voltage applied, it follows that the formula

             

 

is true only for sine wave voltages.

 

You can use the two methods discussed above for determining capacitive reactance by applying them to the circuit shown in figure 4-8.  If you place AC voltmeters across R and C and insert an AC ammeter in the circuit you get the readings as indicated in the figure.

 

These values are actual meter readings.  Now since you have the circuit current measured, you can calculate the capacitive reactance of C by

             


Without knowing the circuit current, you can calculate capacitive reactance with

 

             

 

Notice in figure 4-8 that more voltage is dropped across R and C than is applied from the generator.  The introduction of the capacitor in the circuit has produced a strange circuit behavior.  This is because the capacitor causes a phase shift between the voltage and current.  Therefore you must use vectors to calculate circuit voltage and current.  Vectors for series RC circuits will be discussed later.

 

 

Figure 4-7.  Relationship Between Capacitive Reactance (Xc) and Frequency (f).

 

 

Figure 4-8.  AC Voltmeters Across an RC Circuit.

 


Phase Relationship in a Pure Capacitive Circuit

 

The current flowing through a capacitor at any instant depends on the rate at which the voltage across it is changing.  Therefore, with a sine wave voltage applied, the current is maximum when the voltage is crossing the zero axis, because the voltage is then climbing or falling most rapidly.  When the applied voltage is at its maximum, it is no longer climbing or falling.  As it levels off, the current falls to zero.  The relationship between current and voltage is shown in figure 4-9.

 

The voltage and current are seen to be one-quarter cycle, or 90o apart.  Since the positive alternation of current reaches maximum before that of voltage, current leads the voltage.  The phase or time relationship between these two sine waves is also shown by vectors in figure 4-9.  The general statement can be made that when a sine wave of voltage is applied to a pure capacitance circuit, the current leads the voltage by 90o.

 

 

Figure 4-9.  Phase Relationship Between Current and Voltage in a Pure Capacitive Circuit.

 

Types of Capacitors

 

The major types of capacitors used in electronics and other electrical devices are, mica, ceramic, impregnated paper, air, and electrolytic.

 

Mica.  The mica capacitor is thin metal plates separated by sheets of mica.  The smaller sizes may be only two plates; larger sizes are numbers of plates and mica sheets.  Alternate plates are connected together to provide a large plate area.  The general arrangement is shown in figure 4-10.  For electrodes, some mica capacitors use thin layers of silver deposited directly on the surface of the mica.  A mica capacitor with molded bakelite case and wire terminals is shown in figure 4-11.  Mica capacitors are made in small capacitances up to about 0.5 mfd.  They can be made for very high voltages, to a high degree of accuracy, and very stable under temperature changes.  They are highly suitable for use in high frequency circuits.

 


Ceramic.  Ceramic capacitors have most of the desirable qualities of mica capacitors and, in addition, may be made with a positive or negative temperature coefficient of capacitance.  That is, the capacitance may be made to increase or decrease with changes in temperature.  Such capacitors are very useful in compensating for temperature changes in nearby circuit components.  The ceramic capacitor is made by depositing silver on the surfaces of a ceramic tube (figure 4-12).

 

 

Figure 4-10.  Mica Capacitor Showing Mica and Metal Sheets.

 

 

Figure 4-11.  Molded Mica Capacitor (Enlarged).

 

 

...

Zgłoś jeśli naruszono regulamin