YAESU--CAT-GS-232A-User-Manual.pdf

(291 KB) Pobierz
名称未設定-2
GS-232A
Computer Control Interface
for Antenna Rotators
YAESU MUSEN CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
YAESU U.S.A.
17210 Edwards Rd., Cerritos, CA 90703, U.S.A.
YAESU EUROPE B.V.
P.O. Box 75525 1118 ZN, Schiphol, The Netherlands
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
YAESU GERMANY GmbH
Am Kronberger Hang 2, D-65824 Schwalbach, Germany
YAESU HK LTD.
11th Floor Tsim Sha Tsui Centre, 66 Mody Rd.,
Tsim Sha Tsui East, Kowloon, Hong Kong
199626835.004.png 199626835.005.png 199626835.006.png
199626835.007.png 199626835.001.png
GS-232A Computer Control Interface
for Yaesu Antenna Rotators
The GS-232A provide digital control of most models of
Yaesu antenna rotators ÷ from the serial port of an external
personal computer.
matically step the antenna through up to 3800 angles at
programmable intervals, such as for tracking band open-
ings or satellites (with an elevation rotator).
The GS-232A contains its own microprocessor with ROM
and RAM (memory), and a l0-bit analog-to-digital (A-D)
converter. The 3-wire async serial line can be configured for
serial data rates from 150 to 9600 baud. The GS-232A has a
DB-9 “male” connector for connection to the (RS-232C)
COM port of your computer. Purchase or construnct a
“straight” type serial cable, ensuring it has the correct gen-
der and number of pins for connection to your system.
Please read this manual carefully to install the GS-232A . If
also installing a G-400 , G-500A or G-550 with the GX-500
Automatic Control Adapter, follow the procedures in the
GX-500 manual before installing the GS-232A .
÷ G-800DXA / G-1000DXA / G-2800DXA Azimuth Rotator,
G-800DXC / G-1000DXC / G-2800DXC Azimuth Rotator,
G-400 Azimuth Rotator,
G-500A / G-550 Elevation Rotator,
G-5400B / G-5600B / G-5500 A Z -E L Rotator, and
above Azimuth and Elevation rotator combination.
G-400 Azimuth Rotator and G-500A / G-550 Elevation Rotator requires
one GX-500 Automatic Control Adapter each.
Firmware on the GS-232A supports either direct keyboard
control, or commands from programs written specifically to
support it (software is not supplied by Yaesu). In addition
to reading and setting antenna angle and rotation speed,
the firmware includes clocked positioning routines to auto-
1
 
G ENERAL
Power Requirements : DC 12 V, 110 mA
Case Size :
C ONNECTOR P INOUTS
110 (W) x 21 (H) x 138 (D) mm
Serial I/O :
9-pin DB-9 connector ( RS-232C connector)
Pin 2 - Tx Data
Pin 3 - Rx Data
Pin 5 - Signal Ground
Weight (approx.):
380 g
Semiconductors
Microprocessor : HD6303XP
ROM : 27C64
RAM : 6264
A/D Converter : HD46508PA (10 bits)
Serial Comms : 3-wire Async. DCE
RS-232C voltage levels,
150 to 9600 baud, 8 data bits,
1 stop bit, no parity, no handshake
Rotator Control :
5-pin connector ( EL connector)
Pin 1 - UP switch (open collector)
Pin 2 - DOWN switch (open collector)
Pin 3 - analog output (0.5 - 4.5 V, four steps)
Pin 4 - analog input (0-5V elevation)
Pin 5 - analog ground
5-pin connector ( AZ connector)
Pin 1 - RIGHT switch (open collector)
Pin 2 - LEFT switch (open collector)
Pin 3 - analog output (0.5 - 4.5 V, four steps)
Pin 4 - analog input (0-5V azimuth)
Pin 5 - analog ground
2
199626835.002.png
S UPPLIED A CCESSORIES
¥ Control cable for the Azimuth Rotator ÷ 1 ................ 1 pc
(“5-pin” 1 “Min-DIN” cable)
¥ Control cable for the A Z /E L Rotator ÷ 2 .................... 1 pc
(“Dual 5-pin” 1 “DIN” cable)
¥ DC cable w/coaxial plug ......................................... 1 pc
¥ Hook & loop fasteners (for mounting) ................... 1 pc
A VAILABLE O PTIONS
GX-500 ( GS-232A version ) Control Adapter
(Check with your dealer)
C-1000 Connection Cable
(for SDX series Azuimuth Rotator)
NC-72B/C/F/U ÷ 3 AC Adapter
÷ 3 : B suffix is for use with 117 VAC,
C suffix is for use with 220-240 VAC,
F suffix is for use with 220 VAC, or
U suffix is for use with 230 VAC
÷ 1: G-5400B-G-5600B/G-5500
÷ 2: G-800DXA / G-1000DXA / G-2800DXA &
G-800DXC / G-1000DXC / G-2800DXC
3
199626835.003.png
Zgłoś jeśli naruszono regulamin