X495_sm.pdf

꣏

1-1. GSM General Specification

G S M 8 5 0

P h a s e 1

D C S 1 8 0 0

P h a s e 1

P C 1 9 0 0

P h a s e 1

F r e q . B a n d [ M H z ]

U p l i n k / D o w n l i n k

8 2 4 ~ 8 4 9

8 6 9 ~ 8 9 4

1 7 1 0 ~ 1 7 8 5

1 8 0 5 ~ 1 8 8 0

1 8 5 0 ~ 1 9 1 0

1 9 3 0 ~ 1 9 9 0

A R F C N r a n g e

1 2 8 ~ 2 5 1

5 1 2 ~ 8 8 5

5 1 2 ~ 8 1 0

T x / R x s p a c i n g

4 5 M H z

9 5 M H z

8 0 M H z

M o d . B i t r a t e /

B i t P e r i o d

2 7 0 . 8 3 3 k b p s

3 . 6 9 2 u s

2 7 0 . 8 3 3 k b p s

3 . 6 9 2 u s

2 7 0 . 8 3 3 k b p s

3 . 6 9 2 u s

T i m e S l o t

P e r i o d / F r a m e P e r i o d

5 7 6 . 9 u s

4 . 6 1 5 m s

5 7 6 . 9 u s

4 . 6 1 5 m s

5 7 6 . 9 u s

4 . 6 1 5 m s

M o d u l a t i o n

0 . 3 G M S K

M S P o w e r

3 3 d B m ~ 5 d B m

3 0 d B m ~ 0 d B m

P o w e r C l a s s

5 p c l ~ 1 9 p c l

0pcl ~ 15pcl

S e n s i t i v i t y

- 1 0 2 d B m

- 1 0 0 d B m

T D M A M u x

C e l l R a d i u s

3 5 K m

2 K m

SAMSUNG Proprietary-Contents may change without notice

1-2. GSM TX power class

TX Power

control level

GSM850

TX Power

control level

DCS1800

TX Power

control level

PCS1900

33±2 dBm

30±3 dBm

31±2 dBm

28±3 dBm

29±2 dBm

26±3 dBm

27±2 dBm

24±3 dBm

25±2 dBm

22±3 dBm

23±2 dBm

20±3 dBm

21±2 dBm

18±3 dBm

19±2 dBm

16±3 dBm

17±2 dBm

14±3 dBm

15±2 dBm

12±4 dBm

13±2 dBm

10±4 dBm

11±3 dBm

8±4dBm

9±3dBm

6±4 dBm

7±3 dBm

4±4 dBm

5±3 dBm

2±5 dBm

0±5 dBm

SAMSUNG Proprietary-Contents may change without notice

2-1. SGH-X495 RF Circuit Description

2-1-1. RX PART

- ASM(U100) ꇦ Switching Tx, Rx path for GSM850, DCS1800, PCS1900 by logic controlling.

- ASM Control Logic (U100) ꇦ Truth Table

VC1

VC2

VC3

Tx Mode (GSM850)

Tx Mode (DCS1800/1900)

Rx Mode (GSM850)

Rx Mode (DCS1800)

Rx Mode (PCS1900)

- FILTER

To convert Electromagnetic Field Wave to Acoustic Wave and then pass the specific frequency band.

- GSM FILTER (F101) ꇦ For filtering the frequency band between 869 and 894 MHz

- DCS FILTER (F102) ꇦ For filtering the frequency band between 1805 and 1880 MHz.

- PCS FILTER (F100) ꇦ For filtering the frequency band between 1930 and 1990 MHz.

- VC-TCXO (OSC101)

This module generates the 26MHz reference clock to drive the logic and RF. After division by two a reference clock of

13MHz is supplied to the other parts of the system through the pin CLKOUT. After additional process, the reference

clock applies to the U100 Rx IQ demodulator and Tx IQ modulator. And then, the oscillator is controlled by serial data

to select channel and use fast lock mode for GPRS high class operation.

- Transceiver (U101)

The receiver front-end which amplifies the GSM, DCS aerial signal, converts the chosen channel down to a low IF signal

of 100 kHz. The first stages are symmetrical low noise amplifiers (LNAs). The LNAs are followed by an IQ down mixer.

It consists of two mixers in parallel but driven by quadrature out of phase LO signals. The In phase (I) and Quadrature

phase (Q) IF signals are low pass filtered to provide protection from high frequency offset interferes. The low IF I and Q

signals are then fed into the channel filter. The front-end low IF I and Q outputs enter the integrated bandpass channel

filter with provision for five 8 dB gain steps in front of the filter.

2-1-2. TX PART

I and Q baseband signals are applied to the IQ modulator that shifts the modulation spectrum up to the transmit IF. It is

designed for low harmonic distortion, low carrier leakage and high image rejection to keep the phase error as small as

possible.

SAMSUNG Proprietary-Contents may change without notice

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika: